Atlanta Attachment Company 1390BX Technical Manual & Parts Lists Download Page 32

Page: 32 / 172

Technical Manual & Parts Lists

Light Tower Indicator

The LIGHT TOWER is designed to help the operator/mechanic in
machine operation and troubleshooting.



YELLOW LIGHT ON

means that the machine is out of the

Top or the Bottom film. (Heaters On)



RED LIGHT ON

means that one or both side doors are

open, or the Pull (red) Cable switch is activated. (Heaters On)



RED LIGHT FLASHING

means the seal bars are too hot.



GREEN LIGHT ON

means that the machine is ready to run.

It comes on as soon as the POWER ON button is pressed, and
there are no faults to prevent the machine from running.



GREEN LIGHT FLASHING

means the seal bars are

heating up and have not yet reached operating temperature.

Note: To start the machine, the MACHINE START button on the
touch screen may need to be pressed.



ALL LIGHTS OFF

means that one or more of the E-STOP buttons are pressed, or the Main

Power is turned OFF, or otherwise disabled.

Note:

If the above indications do not solve the problem, please refer to “Troubleshooting” on page 44 of

this manual for additional help or call Atlanta Attachment Company’s service department at 770-963-
7369.

Summary of Contents for 1390BX













































































































































































Search results

Summary of Contents for 1390BX

Reviews:

Related manuals for 1390BX

Brands by name

Popular brands

Atlanta Attachment Company 1390BX, Technical Manual & Parts Lists

Search results

Summary of Contents for 1390BX

Reviews:

Related manuals for 1390BX

Brands by name

Popular brands