ATIM ACW-LW8 Installation Manual Download Page 8

ACW-MR2_QIG_FR_V2.5           - Complete technical manual available at www.atim.com 

 

8

 

b.

 

Mode of operation:  

 

Parameter code (1 byte)

 

Parameter value (2 bytes)

 

0x0A 

The possible values are: 

0x00 = meter mode with transmission every 10 minutes 
0x01 = meter mode with transmission every 6 hours 
0x02 = meter mode with transmission every hour 
0x03 = meter mode with transmission every 3 hours 
0x04 = meter mode with transmission every 30 minutes 
0x05 = meter mode with transmission every 12 hours 
0x06 = meter mode with transmission every 24 hours 
0x07 = meter mode with transmission every 48 hours 
0x08 = digital mode with polling of wirecut input 
0x09 = digital mode with radio transmission on falling edge 
0x0A = digital mode with radio transmission on rising edge 
0x0B = digital mode with radio transmission on falling and 
rising edges 
0x0C = ELEC mode with readings every 10 m 
transmission once per hour 
0x0D = ELEC mode with readings every 30 m 
transmission every 3 hours 
0x0E = ELEC mode with readings once per hour + 
transmission every 6 hours 
0x0F = N/A 
0x10 = use the DIP switch configuration 

Reminder: By default, the product uses the configuration indicated by the DIP switches if no 
configuration has been specified via downlink frames. If a configuration has been applied via 
downlink, it will be used the next time the device restarts.  

c.

 

Setting meter 1:  

 
The index of meter 1 can be set to any value you choose in the range from 0 to 4294967295. 
 

Command to send 

 

Parameter value (4 bytes)

 

C1050Axxxxxxxx 

 

Possible values for xxxxxxxx (in hexadecimal): 
0x00000000 
to 
0xFFFFFFFF 

 
Example: To set the index of meter 1 to 1000, you must send the command C1050A000003E8 via 
downlink (because 1000 = 3E8 in hexadecimal). 
 

Summary of Contents for ACW-LW8











Reviews: