7
If the saw blade rotates in reverse direction: The electric socket connections have to be checked and corrected by a
qualified electrician. The rotation direction of the saw blade should not be defined before testing.
6. MACHINE SAFETY DATA
6.1.1.
It is not allowed to operate the machine with the protective cover and other protective equipment removed.
6.1.2.
Your machine operates with 400V ~ 3 Phase 50Hz. Let the electric installation of your machine carry out by a qualified
electrician only.
6.1.3.
Lifting, installation, electric, pneumatic maintenance of the machine should be carried out by qualified personnel
only.
6.1.4.
Routine maintenance and scheduled maintenance should be carried out by qualified personnel after unplugging the
machine first.
6.1.5.
Ensure that the machine has been cleaned, tested and maintenance before starting to operate.
6.1.6.
Check the safety devices, power cable and moving parts regularly. Don’t operate the machine before having replaced
defective safety devices or faulty parts
6.1.7.
Never change the circular saw without disconnecting electrical and air power.
6.1.8.
Keep foreign materials away from the working area of the machine, keep away from the machine’s moving parts.
The saw blade continues its rotation for a while after switching off the motor.
Don’t use the machine for purposes other than it has been designed for (cutting of iron and other
ferrous materials).
The safety data have been defined above. In order to prevent physical damage or damage to the
equipment, please read the safety information carefully and keep the manual always in an easy
accessible place.
7. OPERATION
The miter saws PEGASUS / SKAT cut non-ferrous aluminum, PVC profiles and PVC materials. The operator adjusts (manually
via knob) the cutting speed of the saw blade according to the material type to be cut. Inner and outer sharp edges of the
carbide tipped circular saw blade ensures high quality clean cutting results. The cutting lenght can be precisely read and
adjusted using the measuring tape fixed to the back fence.
Start the machine only after proper clamping og the work piece to be cut.
The machine is equipped with horizontal clamps. The clamping positions, either manual or pneumatic clamps, can be
adjusted comfortably according to the material.
At pneumatic clamps the clamp piston can be moved 55 mm.
The clamping cylinders have to be outside of the saw blade moving area.
Don’t operate the saw while it touches the work piece. The saw must be operated only when the head is in the top position.
7.1.
Angular Cutting On The Table
7.1.1.
Press the saw blade downuntil it touches the cutting slot of the table.
7.1.2.
Pull out the snap pin from its slot.
7.1.3.
Pull the table locking Bar to the left to unlock.
7.1.4.
Adjust the desired cutting angle by turning the handle to the right or left.
7.1.5.
The cutting angles 15˚ – 22,5˚ – 30˚ – 45˚ are fixed by releasing the snap. Pull the table locking Bar to the right and
fix the table.
7.1.6.
At the angles 0˚ – 15˚ – 22,5˚ and 30˚, lock the table by pulling the table locking Bar to the right. At intermediate
angles (5˚ – 10˚ – 15˚ – 35˚ – 40˚…etc.) the snap pin does not lock. Fix the angle just by pulling the table locking Bar
to the right.
Always ensure that the clamps are positioned outside of the operation area of the saw blade.
7.2.
Air Pressure Adjustment At Pneumatic Machine
7.2.1.
Pull the adjustment button of the conditioner upwards.
a.
Turning the adjustment button in clockwise direction increases the pressure.
b.
Turning the adjustment nutton in counter clockwise direction decreases the pressure.
c.
Once you read 6-8 Bar on the manometer, push the adjustment button of the conditioner down and lock it in that
position
7.2.2.
Place the material to be cut on the machine table, take the measure the cutting length using the measuring tape on
the back fence, and clamp the work piece (pneumatically or manually).
7.2.3.
Start to operate the saw blade by pressing the Start button.
