Atec A675STS Installation Manual Download | Manualshive

Page: 12 / 13

background image

12

Step 8: Adjusting the Rotation

1. If necessary, the TV can be rotated from -5° to +5° by adjusting the two screws on the rear of the

Wall Plate (1)

as shown in Fig. 5c.

2. To adjust the rotation, loosen these two screws with the

Allen Wrench (4)

about 1/2 turn each, and

gently slide the TV to the left or right depending on your needs.
3. Once the TV is in the correct position, re-tighten the screws by turning the

Allen Wrench (4)

clockwise.

Fig. 5c

Fig. 5d

ROTATION

SWIVEL

TILT

«
...
10
11
12
13
»

Summary of Contents for A675STS














Reviews:

No comments

Related manuals for A675STS

Omnivision VHS PV-C2780

Brand: Panasonic Pages: 185

Brand: Bang & Olufsen Pages: 72

VisionMount VLF220

Brand: Sanus Systems Pages: 38

Brand: Sansui Pages: 48

Brand: IC Pages: 11

Brand: GE Pages: 17

Brand: GE Pages: 24

Brand: GE Pages: 28

Brand: GE Pages: 20

Brand: GE Pages: 16

Brand: GE Pages: 23

Brand: GE Pages: 24

Brand: Haier Pages: 11

Brand: Haier Pages: 10

Brand: Haier Pages: 15

Brand: Haier Pages: 10

Brand: Haier Pages: 9

Brand: Haier Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands