ATD Tools ATD-7454, Owner'S Manual, Page: 4 / 12

4
Size of Hardware Kits Qty
3 Bolt M10x25 12
/RFNZDVKHU
M10 12
1XW
M10 12
9
1XW
M8 2
11 Bolt M16x150 4
M16 8
/RFNZDVKHU M16 4
1XW M16 4
13 Bolt M10x25 4
/RFNZDVKHU M10 4
Square washer M10 4
14 Bolt M10x130 2
/RFNZDVKHU M10 2
1XW M10 2
F
.
)LJXUH $VVHPEO\,OOXVWUDWLRQIRUPRGHO $7'
Assembly
Model ATD-7454: (Refer to Figure 2)
Note:
'RQRWWLJKWHQDQ\EROWVXQOHVVWROGWRGRVR
1. Attach
EDVH OHJV
(1) to
XSULJKW
channels (2) with
EROWV ORFN
washers and nuts (3) . Hand
WLJKWHQ
only.
2. Attach lower cross
PHPEHU
(4) to
XSULJKW
channels
(2) ZLWKEROWVORFNZDVKHUVDQGQXWV (3).
3. Attach support OLQNV (5) to the EDVH (1) and XSULJKW
channels (2) with EROWV ORFN washers and nuts (3) .
4. Carefully slide EHG frame (6) down to lowest SRVVLEOH
SRVLWLRQEHWZHHQWKHXSULJKWFKDQQHOV (2) .
5. Attach the screw KRRNV (7) to the MDFN EUDFNHW (8)
with nuts (9) .
/HDYH
nut
XQWLJKWHQHG
to provide
HDVLHUVSULQJDWWDFKPHQWODWH
r.
6. Slide the
MDFN EUDFNHW
(8) down
EHWZHHQ XSULJKW
FKDQQHOVRQWRWKHEHGIUDPH
(6) .
7. Attach upper cross
PHPEHUV
(10) to
XSULJKW
channels (2)
and nuts (11) .
8. Attach head plate (12) to upper cross PHPEHUV (10)
ZLWKEROWVORFNZDVKHUVDQGVTXDUHZDVKHUV (13) .
9. Attach two EROWV ORFN washers and nuts (14) thru the
upper cross PHPEHU (10) . Then attach one end of
the
VSULQJV
(15) to the
EROWV
(14) and the other end
WRWKHVFUHZKRRNV
(7)
RQWKHMDFNEUDFNHW
10. Carefully place the
ERWWOH MDFN
(16)
EHWZHHQ
the
head plate (12) and
MDFN EUDFNHW
(8). T
LJKWHQ
the
nuts (9) that hold screw
KRRNV
(7) to prevent
MDFN
IURPLQDGYHUWHQWO\IDOOLQJRXW
11. Tighten all applicable nuts and bolt assemblies.
&DUHIXOO\EULQJWKHEHGIUDPH (6) up and secure it
with pins (19) .
3ODFHWKH DUERU3ODWHV (17) RQEHGIUDPH (6) .
14.The press is now ready to use. 'RQ¶W IRUJHW to insert
the handle (18) LQWRKDQGOHVOHHYHRIERWWOHMDFN
NOTICE: Before disassembly, carefully slide bed to
its fully lowered position.
1
4
2
3
5
6
17
18
19
7
15
10
11
16
12
8
9
3
14
13