background image

SAFETY WARNING AND PRECAUTIONS

General Safety Warnings:

WARNING:

The instru

ĐƟ

ons and warnings contained in this manual should be read and understood before using

or opera

Ɵ

ng this tool. Do not allow anyone to use or operate this tool un

Ɵ

l they have read this manual and have

developed a thorough understanding of how this tool works. Failure to observe any of the following instru

ĐƟŽŶƐ

could

result in severe personal injury to tool user and bystanders, or cause damage to the tool and property. Keep this manual
for future reference.

Note:

The warnings and cau

Ɵ

ons discussed in this instru

ĐƟ

on manual cannot cover all possible condi

Ɵ

ons and

situa

Ɵ

ons that may occur. It must be understood by the operator that common sense and cau

Ɵ

on are factors which

cannot be built into this product, but must be supplied by the operator.

WARNING:

Use safety equipment. User and bystanders should use safety goggles or safety glasses with side shields

which comply with current na

Ɵ

onal standards, or when needed, a face shield. Use an ANSI approved dust mask or respirator

when working around metal, wood, and chemical dusts and mists. This applies to all persons in the work area. Also use
non skid safety shoes, hardhat, gloves, dust collec

Ɵ

on systems, and hearing protec

Ɵ

on when appropriate.

WARNING:

Keep bystanders and children out of the work area while opera

Ɵ

ng this tool.

WARNING:

Always keep your work area clean, unclu

Ʃ

ered, and well lit. Clu

Ʃ

ered or dark areas invite accidents and

injuries. DO NOT work on

Ň

oor surfaces that are slippery.

WARNING:

Do not operate this tool if you are

Ɵ

red or under the in

ŇƵ

ence of alcohol, drugs, or medica

Ɵ

ons that could

a

ī

ect your ability to use the tool properly.

WARNING:

Dress properly. Do not wear loose clothing or jewelery as they can be caught in moving parts. Wear

restric

Ɵ

ve hair covering to contain long hair.

WARNING:

Do not reach over or across running machines. Keep proper foo

Ɵ

ng and balance at all

Ɵŵ

es. Non skid

footwear is recommended when working.

Product

^ƉĞĐŝĮĐ Warnings:

Non compliance with these warnings may result in injury or damage to the jack or the vehicle.

WARNING:

NEVER use hydraulic jack as a stand alone device. A

Ō

er li

Ō

ing, IMMEDIATELY support the li

Ō

ed

vehicle with a pair of appropriately rated jack stands. NEVER place ANY po

ƌƟ

on of your body beneath the vehicle when

l

ŝŌ

ing OR lowering.

WARNING:

Do not modify the jack in any way.

WARNING:

Never exceed the rated capacity of the jack.

WARNING:

This jack is a li

Ō

ing device only and should never be used to move the vehicle.

WARNING:

The jack should be supported on a solid and level ground. Never use the jack in a surface where it may

sink into the ground.

Summary of Contents for ATD-7343








Reviews: