AT&T OneVision DEFINITY G3 Guide Installation And Connection Manual Download

Page: 123 / 287

Issue 2 April 1996

6-9

Connectivity
Digital Connections

4. Circuit pack (DCP, BRI, DS-1, or PRI)

5. Cross connect at main distribution frame

6. Site-specific network connections

7. Data module or ADU

8. Proxy Agent PC

Diagram 4:
DEFINITY
G3i, G3s,
G3vs

The digital, dial-up connection for a DEFINITY G3i, G3s, or G3vs
follows.

Legend for Diagram 4: DEFINITY G3i, G3s, G3vs

1. DEFINITY G3i, G3s, or G3vs, G1, or system 75 R1v3 PBX

2. Netcon port

3. Circuit pack (DCP, BRI, DS-1, or PRI)

4. Site-specific network connections

Summary of Contents for OneVision DEFINITY G3 Guide
































































































































































































































































































Search results

Summary of Contents for OneVision DEFINITY G3 Guide

Reviews:

Related manuals for OneVision DEFINITY G3 Guide

Brands by name

Popular brands

AT&T OneVision DEFINITY G3 Guide, Installation And Connection Manual

Search results

Summary of Contents for OneVision DEFINITY G3 Guide

Reviews:

Related manuals for OneVision DEFINITY G3 Guide

Brands by name

Popular brands