ATAGO 3574 Instruction Manual Download Page 51

Page: 51 / 57

14. Definitions of Error Messages

Measurement value display

Error message

Explanation

Action

L.LLLLL

In Refractive index (nD) mode, the sample measured

below the lower limit of the measuring range, or

measurement was made with air contacting the

prism.

Measure a sample within the measuring

range.

LLLL.LL

In Brix mode, the sample measured below the lower

limit of the measuring range, or measurement was

made with air contacting the prism.

Measure a sample within the measuring

range.

LLLLLL

In Concentration mode, the sample measured below

the lower limit of the measuring range, or

measurement was made with air contacting the

prism.

Measure a sample within the specified

concentration and temperature range.

H.HHHHH

In Refractive index (nD) mode, the sample measured

above the upper measurement limit.

Measure a sample within the measuring

range.

HHHH.HH

In Brix mode, the sample measured above the upper

measurement limit.

Measure a sample within the measuring

range.

HHHHHH

In Concentration mode, the sample measured above

the upper measurement limit.

Measure a sample within the specified

concentration and temperature range.

H.over

The alarm setting LED light comes on when the

sample measured is above the upper limit.

Measure samples within the upper limit.

L.over

The alarm setting LED light comes on when the

sample measured is below the lower limit.

Measure samples within the lower limit.

E.EEEEE

The LED light source has been depleted (in refractive

index (nD) mode).

―――――――――

EEEE.EE

The LED light source has been depleted (in Brix

mode).

―――――――――

EEEEEE

The LED light source has been depleted (in

concentration mode).

―――――――――

E-8002

An error is present in the connection between the

detection and display sections.

Check the connection of each section.

Turn on the power switch again.

Clean the prism.

d Err

The sample temperature measured in the Conc

mode is above the programmed range.

Measure a sample within the specified

concentration and temperature range.

※

- - - - - - is displayed during the time a measurement is being taken.

Temperature display

Error message

Explanation

Action

LLLL

The sample temperature is -5.

１

˚C or lower.

Measure a sample within the measuring

range.

HHHH

The sample temperature is 160.1˚C or higher.

Measure a sample within the measuring

range.

Flashing

temperature

value

The prism temperature is below 5˚C or above 100˚C.

In this case, the displayed Brix(%) value is not

properly corrected for temperature.

―――――――――

Summary of Contents for 3574


























































Search results

Summary of Contents for 3574

Reviews:

Related manuals for 3574

Brands by name

Popular brands

ATAGO 3574, Instruction Manual

Search results

Summary of Contents for 3574

Reviews:

Related manuals for 3574

Brands by name

Popular brands