manualshive.com logo in svg

Atag VA6011AT, User Instructions

Share
Download
Atag VA6011AT User Instructions Download Page 11

Operating Instructions

11

Setting the water softener

Using the table as a guide, adjust the water softener to that which cor-
responds to the hardness of the water in your area: 

0 

The dishwasher must be switched off. 

Manual setting:

1.

Open the dishwasher door.

2.

Remove the lower basket from the 
dishwasher.

3.

Turn the hardness range switch to 0 
or 1 (see table).

4.

Replace the lower basket. 

Electronic setting:

1.

Press the ON/OFF button.
The LED in the ON/OFF button will become illuminated.

3 

If other indicators are also illuminated, this means that a programme 
has been activated. The programme must be cancelled (RESET):
Press function buttons 

1

and

2 

simultaneously for approx. 2 seconds. 

All other indicators will go out.

2.

Press the function buttons 

1

 and 

2

 simultaneously and keep them 

pressed until the LED indicators for function buttons 1 and 3 will flash.

3.

Press function button 

1

 again.

The LED indicator for function button 

1 

will flash.

The LED indicator for the end of the wash programme will flash 
simultaneously:
– The number of times that the LED indicator for the end of the wash 

programme flashes corresponds to the hardness setting. 

– This sequence of flashes is repeated many times, with a 3 second 

pause in between.

4.

Pressing function button

1

increases the hardness setting by 1 degree.

(Exception: hardness setting 1 follows hardness setting 10).

5.

When the hardness setting is correct, press the ON/OFF button.
The hardness setting is now saved. 

1) The water hardness will only be indicated acoustically if the acoustic signal has 

been activated.

2) (°d) German degree, measure of the hardness of water
3) [mmol/l] millimol per litre, international unit for the hardness of water
4) On this setting the length of the dishwashing cycle may be slightly longer.
*) Factory setting

Summary of Contents for VA6011AT

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands