Asyril Asycube 240 Operating Manual Download Page 19

Page: 19 / 52

Asycube 240

Operating Manual

000.100.500

Version: A6

000.100.500

Asycube 240

- Operating Manual

19/52

Communication

The communication with the Asycube is

established

standard

Ethernet

communication via RJ45 port

(A)

Characteristic

Value

Default IP
address

192.168.127.254

Default subnet
mask

255.255.255.0

Port

4001

MAC address

Can be read by
ARP request

For more information on the procedure to

restore the default IP address, please see

chapter 4.3.2.

Figure 2-12 : Ethernet connection RJ45

Backlight Synchronization

A standard M8 three-pins female cable

enables to synchronize camera acquisition

and Asycube backlight illumination, it must

be connected as follows :

Pin

Signal

Cable

(option)

(1)

Not wired

braun

(3)

0V GND

blue

(4)

+24 V pulse

(illumination synch.)

black

Connector type (on Asycube side) :

M8, 3P, male

Figure 2-13 : Backlight synchronization

NOTE :

The Asycube Backlight illumination time corresponds to the length of the pulse signal.

(A)

(3)

(4)

(1)

Summary of Contents for Asycube 240





















































Search results

Summary of Contents for Asycube 240

Reviews:

Related manuals for Asycube 240

Brands by name

Popular brands

Asyril Asycube 240, Operating Manual

Search results

Summary of Contents for Asycube 240

Reviews:

Related manuals for Asycube 240

Brands by name

Popular brands