Asus Z9NA-D6 Manual Download

Page: 156 / 188

6-8

Chapter 6: Driver installation

3. Select

Yes

using the <Tab> key when asked if you have the driver disk, then

press <Enter>.

Main Menu

Do you have a driver disk?

Yes

4. Insert the Red Hat

Enterprise RAID driver disk to the USB floppy disk drive,

select

, then press <Enter>.

The drivers for the RAID card are installed to the system.

Insert Driver Disk

Insert your driver disk into /dev/fd0

and press “OK” to continue.

Back

Red Hat

Enterprise Linux OS 5.6

To install the LSI MegaRAID controller driver when installing Red Hat

Enterprise

OS:
1. Boot the system from the Red Hat

OS installation CD.

2. At the

boot:

, type

linux dd noprobe=ata1 noprobe=ata2...

, then

press <Enter>.

The number of ata varies with the hard disk drive number you have when

building a RAID set. For example, if you want to build a RAID set with 6 hard

disk drives, type command line:

linux dd noprobe=ata1 noprobe=ata2

noprobe=ata3 noprobe=ata4 noprobe=ata5 noprobe=ata6

- To install or upgrade in graphical mode, press the <ENTER> key.
- To install or upgrade in text mode, type: linux text <ENTER>.
- Use the function keys listed below for more information.

[F1-Main] [F2-Options] [F3-General] [F4-Kernel] [F5-Rescue]

boot: linux dd noprobe=ata1 noprobe=ata2

Summary of Contents for Z9NA-D6





























































































































































































Search results

Summary of Contents for Z9NA-D6

Reviews:

Related manuals for Z9NA-D6

Brands by name

Popular brands

Asus Z9NA-D6, Manual

Search results

Summary of Contents for Z9NA-D6

Reviews:

Related manuals for Z9NA-D6

Brands by name

Popular brands