Asus RT-AX89X User Manual Download Page 8

Page: 8 / 138

SPF+ LED

Off

: No SPF+ signal.

: Wireless system is ready.

Flashing

: Transmitting or receiving data via wireless connection.

10GE LED

Off

: No 10GE signal.

: Wireless system is ready.

Flashing

: Transmitting or receiving data via wireless connection.

LAN LED

Off

: No power or no physical connection.

: Has physical connection to a local area network (LAN).

WAN (Internet) LED

Red

: No IP or no physical connection.

: Has physical connection to a wide area network (WAN).

5GHz LED

Off

: No 5GHz signal.

: Wireless system is ready.

Flashing

: Transmitting or receiving data via wireless connection.

2.4GHz LED

Off

: No 2.4GHz signal.

: Wireless system is ready.

Flashing

: Transmitting or receiving data via wireless connection.

Power LED

Off

: No power.

: Device is ready.

Flashing slow

: Rescue mode

WPS button

This button launches the WPS Wizard.

LED On/Off button

This button turns on/off the LED indicators.

Wi-Fi On/Off button

This button enables or disables Wi-Fi.

LAN ports 1 ~ 8

Connect network cables into these ports to establish LAN connection.

WAN (Internet) port

Connect a network cable into this port to establish WAN connection.

10G base T port

This port is for 10G base T connection.

Summary of Contents for RT-AX89X











































































































































Search results

Summary of Contents for RT-AX89X

Reviews:

Related manuals for RT-AX89X

Brands by name

Popular brands

Asus RT-AX89X, User Manual

Search results

Summary of Contents for RT-AX89X

Reviews:

Related manuals for RT-AX89X

Brands by name

Popular brands