Asus P4XP-X User Manual Download Page 38 | Manualshive

Page: 38 / 64

background image

2-8

Chapter 2: BIOS information

Award BIOS Beep Codes

Beep

Meaning

One short beep when

No error during POST

displaying logo

Long beeps in an endless loop

No DRAM installed or detected

One long beep followed by

Video card not found or video card

three short beeps

memory bad

High frequency beeps when

CPU overheated;

system is working

System running at a lower frequency

2.1.4 BIOS beep codes

When you turn the power on and the system runs POST (Power On Self Tests),
you will hear BIOS beeps. Refer to the following table for the meaning of the
beeps.

The recovered BIOS may not be of the same version as the original BIOS. Visit
ASUS website (www.asus.com) to download the latest BIOS for this
motherboard, and update the BIOS using ASUS AFLASH.EXE, ASUS EZ Flash
Utility, or ASUS Live Update.

3. Press Y to start the auto-recovery procedure. If you do not press Y, the system

still performs the auto-recovery after 30 seconds.

Using the bootable floppy disk:

1. Boot the computer using the bootable floppy disk.

2. Execute the AFLASH.EXE utility. See section 2.1.2 for the procedure.

3. If the BIOS image is newer than the current BIOS, or if the BIOS is corrupted,

this confirmation message appears.

“Are you sure? (Y/N)”

4. Press Y to update the BIOS.

«
...
36
37
38
39
40
...
»

Summary of Contents for P4XP-X

































































Reviews:

No comments

Related manuals for P4XP-X

Brand: Yamaha Pages: 76

Brand: Lantronix Pages: 8

Brand: Gigabyte Pages: 8

Brand: Mercury Pages: 41

Brand: CIRCUIT DESIGN Pages: 9

Brand: ST Pages: 9

Brand: Supermicro Pages: 90

Brand: P&E Microcomputer Systems Pages: 38

Brand: Atmel Pages: 16

Brand: Freetech Pages: 79

Brand: Vox Pages: 23

Brand: Microchip Technology Pages: 31

Brand: Gigabyte Pages: 80

Brand: ZMDI Pages: 25

Outboard Motor BF5A

Brand: Honda Pages: 84

Brand: AOpen Pages: 8

Brand: JETWAY Pages: 45

Brand: Foxconn Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands