Asus M2N68-LA User Manual Download Page 19

Page: 19 / 22

M2N68-LA (Narra 3)

6. CPU and Chassis fan connectors (3-pin CPU_FAN,.

3-pin CHASSIS_FAN1)

The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or

a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan

connectors on the motherboard, making sure that the black wire of each cable

matches the ground pin of the connector.

M2N68-LA

M2N68-LA Fan connectors

CPU_FAN

CHASSIS_FAN1

GND

Rotation

+12V

GND

Rotation

+12V

Do not forget to connect the fan cables to the fan connectors. Insufficient air

flow inside the system may damage the motherboard components. These are

not jumpers! DO NOT place jumper caps on the fan connectors.

M2N68-LA

M2N68-LA Front audio connector

F_AUDIO

AUD_GND AUD_VCC AUD_RET_R AUD_VCC AUD_RET_L

AUD_MIC1 AUD_MIC2

AUD_FPOUT_R

AUD_MIC_JD

AUD_FPOUT_L

PIN1

7. Front panel audio connector (10-1 pin F_AUDIO)

This connector is for a chassis-mounted front panel audio I/O module that

supports Azalia audio standard.

Summary of Contents for M2N68-LA























Search results

Summary of Contents for M2N68-LA

Reviews:

Related manuals for M2N68-LA

Brands by name

Popular brands

Asus M2N68-LA, User Manual

Search results

Summary of Contents for M2N68-LA

Reviews:

Related manuals for M2N68-LA

Brands by name

Popular brands