manualshive.com logo in svg

Asus KFN4-DRE - Motherboard - SSI EEB 3.51, Manual, Page: 43 / 122

Share
Download
Asus KFN4-DRE - Motherboard - SSI EEB 3.51 Manual Download Page 43

ASUS KFN4-DRE

2-23

2.  IDE connectors (40-1 pin PRI_IDE1, SEC_IDE1)

The onboard IDE connectors are for Ultra DMA 133/100/66 signal 

cables. There are three connectors on each Ultra DMA 133/100/66 

signal cable: blue, black, and gray. Connect the blue connector to 

the motherboard’s IDE connector, then select one of the following 

modes to configure your device(s).

•  Pin 20 on the IDE connector is removed to match the covered hole 

on the Ultra DMA cable connector. This prevents incorrect insertion 

when you connect the IDE cable.

•  Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices.

Black or gray 

 

Drive jumper 

Mode  

Cable  

 

 

setting  

of device(s) 

connector

Single device 

Cable-Select or Master    - 

Black 

Two devices 

Cable-Select 

Master 

Black 

 

 

Slave 

Gray 

 

Master 

Master 

 

 

Slave 

Slave 

 

If any device jumper is set as “Cable-Select,” make sure all other device 

jumpers have the same setting.

R

KFN4-DRE

KFN4-DRE IDE Connectors

PRI_IDE1

SEC_IDE1

NOTE: 

Orient the red markings

(usually zigzag) on the ID

ribbon cable to PIN 1.

PIN1

PIN1

Summary of Contents for KFN4-DRE - Motherboard - SSI EEB 3.51



























































































































Reviews:

No comments