Asus Aaeon BOXER-8254AI User Manual Download Page 24

Page: 24 / 42

Chapter 2

–

Hardware Information

mp
act

Fan

less
E

mb
ed

ded

AI@
Ed

BO
XE

R-

8254

2.4 List of Connectors

The board has a number of connectors that allow you to configure your system to suit
your application.

The table below shows the function of each of the board's connectors

Label

Function

CN1

NVIDIA Xavier NX Module Connector

CN2

RTC Battery Connector

CN3

Front Panel Connector

CN4

Recovery micro-USB Connector

CN5

HDMI Connector

CN6

RS232/RS485 DSUB-9P Connector

CN7

CANBus DSUB-9P Connector

CN8

UART Debug Header

CN10

microSD Card Socket

CN11

M.2 E-Key Socket

CN12

SIM Card Socket

CN14

Dual USB2.0 Connector

CN15

USB3.2 Gen 2/USB2.0 Dual Port Connector

CN16

Internal USB2.0 Header

CN17

Dual Gigabit LAN Connector

CN18

SATA Power Connector (5V)

CN19

SATA Connector

CN20

2-pin 24V Power In

CN24

6-bit GPIO

CN37

8-bit GPIO Header

CN47

Internal COM RS232 Header

SW1

CN6 RS232/485 Selection

Summary of Contents for Aaeon BOXER-8254AI











































Search results

Summary of Contents for Aaeon BOXER-8254AI

Reviews:

Related manuals for Aaeon BOXER-8254AI

Brands by name

Popular brands

Asus Aaeon BOXER-8254AI, User Manual

Search results

Summary of Contents for Aaeon BOXER-8254AI

Reviews:

Related manuals for Aaeon BOXER-8254AI

Brands by name

Popular brands