background image

6

 CUSL-L User’s Manual

2.1 The CUSL-L

The CUSL-L motherboard is carefully designed for the demanding PC user who
wants advanced features processed by the fastest processors.

2.1.1 Specifications

Latest Intel Processor Support
Pentium III™

100/133MHz FSB

FC-PGA370

Celeron™

66MHz FSB

FC-PGA370

North Bridge System Chipset: The Intel

®

 Solano™ 82815 chipset (N.B. 544

BGA) supports a 66/100/133 Front Side Bus (FSB), up to 512MB of PC100/
PC133 SDRAM, internal graphics  AGP 2.0 and universal AGP slot support.

South Bridge System Chipset: The Intel I/O Controller Hub 1 (ICH1) features
support for UltraDMA/66, which allows burst mode data transfer rates of up to
66MB/sec.

Intel

®

 Accelerated Hub Architecture: Features a dedicated high speed hub

link between the ICH1 and GMCH with a bandwidth of 266MB/sec – twice the
maximum bandwidth of the PCI bus.

Onboard Audio: Features AC’97 2.1 Compliant ICH1 Internal Audio Control-
ler and Cirrus Logic CS4299 Codec..

PC100/PC133 Memory Support: Equipped with two Dual Inline Memory Mod-
ule (DIMM) sockets to support PC100/PC133-compliant SDRAMs (available in
64, 128, 256, 512MB densities) up to 512MB.

Solano Internal Graphics: Integrated graphics support (AGP 2.0 ).

Universal AGP Slot: Comes with an Accelerated Graphic slot that supports
AGP cards for high performance, component level interconnect targeted at 3D
graphical applications using a 1X, 2X  or 4X mode bus. (Backward compatible
to support AGP 4X and AGP 2X. This slot can also support an AGP  Inline
Memory Module (AIMM) for up to 4MB of 133MHz SDRAM display cache.)

UltraDMA33/66 Support: Comes with an onboard PCI Bus Master IDE con-
troller with two connectors that support four IDE devices on two channels. Sup-
ports UltraDMA/66, UltraDMA/33, PIO Modes 3 & 4 and Bus Master IDE
DMA Mode 2, and Enhanced IDE devices, such as DVD-ROM, CD-ROM, CD-
R/RW, LS-120, and Tape Backup drives.

Low Pin Count (LPC) Multi-I/O: Provides two high-speed UART compatible
serial ports and one parallel port with EPP and ECP capabilities.

Fault Detection: CPU Fan and Chassis Fan.

PCI Expansion Slots: Provides three 32-bit PCI (PCI 2.2 compliant) expansion
slots. All PCI slots can support Bus Master PCI cards, such as SCSI or LAN
cards. (PCI supports up to 133MB/s maximum throughput.)

Enhanced ACPI & Anti-Boot Virus Protection: Firmware HUB programmable
(Flash EEPROM)BIOS with enhanced ACPI for Windows 98 compatibility, built-
in firmware virus protection, and autodetection of most devices for auto-setup.

Concurrent PCI: Concurrent PCI allows multiple PCI transfers from PCI mas-
ter busses to the memory and processor.

LCD/TV Output: The LCD/TV interface can support either an optional LCD
module for LCD output or a TV-out module for TV output.

2.  FEATURES

Specifications

2.  FEA

TURES

Summary of Contents for 815




























Reviews: