background image

 

2

 

 

 

SAFETY PRECAUTIONS 

Before using this product, carefully read the following safety precautions. 

• 

Immediately report any malfunction to the dealer that performed installation. 

• 

Under no circumstance can this product or its use be modified. 

• 

Always turn off main switch when vehicle is parked in an enclosed, unventilated area or is in 
for servicing. 

• 

Always turn off main switch when not using your Remote Starter for extended periods of time. 

• 

Keep remote controls away from children. 

• 

Have your engine tuned regularly to ensure optimum performance of your Remote Starter. 

• 

Make sure your windshield wipers are turned off before leaving vehicle. 

• 

Regularly check safety features that stop engine (see “SAFETY CHECKS” on page 17.) 

• 

Make sure you comply with all local regulations, which may prohibit leaving your engine 
running when vehicle is unattended in a public place. 

• 

Always advise service personnel that your vehicle is equipped with a Remote Starter equipped 
with a starter cut function. 

• 

We strongly recommend that you have your system checked annually.    
Contact the dealer in your area. 

BEFORE USING YOUR REMOTE STARTER 

Before leaving your vehicle, set the various controls in order to use your Remote Starter. 

• 

Set heating/air-conditioning controls to desired position. (When the remote starter starts your 
engine, it will also turn on your climate control system.) 

• 

Turn your windshield wipers to the “

OFF

” position. 

• 

Make sure gearshift is in “

P

”. 

 

Summary of Contents for QS-5A





















Reviews: