background image

 

8

 

 

When mode is activated:  

Parking lights will flash 4 times, then, if temperature is below preset level, engine will start.  
If temperature is above preset level, system waits until it goes below preset level before starting.  
For the engine to be able to start, a valid safety sequence has to be detected by the system (see "Safety Sequence" on 

page 3). 

If system cannot execute command (for example, safety sequence is not valid, hood is open, etc.), confirmation will be 

different (lights: 3). 

When mode is deactivated:  

Parking lights will flash twice to confirm that mode is deactivated. Applying brakes also deactivates Low Temperature 

mode. 

LOCK/UNLOCK COMMANDS 

(Option 2 only) 

If your vehicle is equipped with electric door locks, several functions can be operated by remote control.  
These features are optional and may require purchasing additional equipment. Consult your dealer for advice.  
Following systems can be controlled: 

• 

Door locks. 

• 

Trunk or hatchback release. 

• 

Interior lights. 

LOCK   

Press the 

 button, doors are locked and parking light flashes once to confirm command has been received.  

Parking light confirmation is sent as many times as command is repeated so you are sure that system has received the 

command.  
When command is repeated, horn sounds once if option "Confirmation on 2nd lock" was set (during installation) and horn 

is connected to system.  

UNLOCK 

 

Press the 

  button, doors are unlocked and parking light flashes twice to confirm command has been received. 

The “Unlock“ function can be configured in such a way that the first Unlock command only unlocks the driver's door, while 

a following Unlock command unlocks the other door(s). 

DOME LIGHT SUPERVISION 

This function is : 

Active

 

 

Inactive

 

 (programmable during installation). 

Dome light will turn on for 30 seconds every time “Unlock” command is sent.  
This 30-second period is cancelled when “Lock” or "Trunk release" command is sent or brakes are applied. 

TRUNK RELEASE   

   

This function is : 

Active

 

 

Inactive

 

 (programmable during installation). 

Press the 

 and 

  buttons simultaneously (lights: 3). Trunk is released and parking lights flash three times to 

confirm command has been received.  
The trunk cannot be released if ignition key is in “

ON

” position. In this case, parking lights flash once to confirm that 

command has been received but trunk could not be released. 

If you are not sure you have received confirmation, repeat command. System will repeat confirmation as often as you 

wish. 
 

Summary of Contents for 803M













Reviews: