Astria CAT36P2 Installation And Operation Instructions Manual Download Page 3

SAFETY

 WARNING: Do not install a 

fireplace insert in this box unless 

the manufacturer's instructions 

with the insert specifically state 

this fireplace has been tested for 

use with this insert.

FOR YOUR SAFETY

•  Do not store or use gasoline 

or any other flammable vapors 

or liquids in the vicinity of this 

or any other appliance.

•  Due to high temperatures, the 

appliance  should  be  located 

out  of  traffic  and  away  from 

furniture and draperies.

•  Do not place clothing or other 

flammable materials on or near 

the appliance.

•  Never  leave  children  unat-

tended when a fire is burning 

in the fireplace.

 WARNING: Use solid wood 

or processed solid fuel fire logs 

only.  When  processed  wood 

fuel fire logs are used, do not 

poke or stir the logs while they 

are burning. Use only fire logs 

that  have  been  evaluated  for 

the application in fireplace and 

refer  to  fire  log  warnings  and 

caution markings on packaging 

prior to use.

This fireplace is not intended to 

be used as a substitute for a fur-

nace to heat an entire home. Use 

for supplemental heat only.

 WARNING: Improper instal-

lation,  adjustment,  alteration, 

service or maintenance can 

cause injury, property damage or 

loss of life. Refer to this manual 

for assistance or additional in-

formation.  Consult  a  qualified 

installer or local distributor.

IMPORTANT: Check local codes 

before installing this fireplace.

Before beginning installation of this fireplace, 

read these instructions through completely.
•  This INNOVATIVE HEARTH PRODUCTS 

fireplace  and  its  components  are  safe 

when installed according to this installation 

manual. Unless you use IHP components, 

which have been designed and tested for 

the fireplace system, you may cause a fire 

hazard.

•  The INNOVATIVE HEARTH PRODUCTS 

warranty  will  be  voided  by  and  IHP  dis

-

claims any responsibility for the following 

actions.

a. Modification  of  the  fireplace,  com

-

ponents,  doors,  air  inlet  system  and 

damper control.

b. Use of any component part not manu

-

factured  or  approved  by  INNOVATIVE 

HEARTH  PRODUCTS  in  combination 

with an IHP fireplace system.

Proper installation is the most important step 

in ensuring safe and continuous operation of 

fireplace. Consult the local building codes as 

to the particular requirements concerned with 

the installation of all factory built fireplaces.

TABLE OF CONTENTS

Safety ..................................................................

3

Specifications ......................................................

4

Fireplace Installation............................................

5

Venting Installation ..............................................

PureFire Installation...........................................

14

Optional Gas Line Installation............................

14

Operation and Maintenance ..............................

15

PureFire Emissions Control System ..................

17

Parts ..................................................................

19

Replacement Parts ............................................

22

Technical Service...............................................

22

Accessories .......................................................

22

Notes .................................................................

25

NOTICE:  The  firebox  canopy 

(hood)  must  not  be  modified 

or  replaced  with  a  canopy  that 

may  be  provided  with  the  un-

vented decorative room heater.

f i r e - p a r t s . c o m

Summary of Contents for CAT36P2





























Reviews: