Astria Fireplaces Tuscan36P2 Installation And Operation Instructions Manual Download Page 13

Astria.us.com

126764-01_F

13

Doors Fully Closed 

Fireplace Front

Doors Fully Opened 

Fireplace Front

OPERATION AND MAINTENANCE GUIDELINES

Figure 21 - Glass Doors

GLASS DOORS

Glass doors are optional with the fireplace. When the fireplace is in 

operation, doors must be fully opened or fully closed position only 

or a fire hazard may be created (see Figure 21).
A fireplace equipped with glass doors operates mush differently 

than a fireplace with an open front. A fireplace with glass doors has 

a limited amount of air for combustion. Excessive heat within the 

fireplace can result if too large a fire is built or if the combustion air 

gate is not completely open. 
The following tips should be followed to assure that both the fireplace 

and the glass door retain their beauty and function properly. Both the 

flue damper and the glass doors must be fully opened before starting 

the fire. This will provide sufficient combustion air and maintain safe 

temperatures in the firebox.

IMPORTANT: 

The glass must be allowed to warm slowly and evenly. 

The tempered glass will withstand a gradual temperature rise to 550° 

F, which is more than a normal fire will generate. Such materials as 

pitch/wax laden logs, very dry mill end lumber and large amounts 

of paper or cardboard boxes can create an excessively hot fire and 

should not be burned in this fireplace. Always keep the fire well back 

from the doors and never allow flames to contact the glass.

 WARNING: Fireplaces equipped with glass doors 

should be operated only with doors fully opened or 

doors fully closed. Doors, if left partly open, may draw 

gas and flame out of the fireplace opening creating 

risks of both fire and smoke.

WARNING: Discontinue use of the appliance imme-

diately if doors are damaged and contact a qualified 

installer for repair. Only doors certified with the ap-

pliance shall be used.

 WARNING: Do not slam or strike doors. Damage 

can result in a hazardous condition.

Cleaning Glass

Clean the glass with any commercial glass cleaner or soap and 

water. Do not use any abrasive material to clean the glass. Do not 

clean the glass with any cool water is the glass is still hot from the 

fire and smoke.
A gas line or gas log lighter may be installed for the purpose of 

installing a vented or vent-free decorative gas appliance incorporat-

ing an automatic shutoff device and complying with the Standard 

for Decorative Gas Appliances for Installation in Vented Fireplaces, 

ANSI Z21.60 or American Gas Association draft requirements for 

Gas Fired Log Lighters for Wood Burning Fireplaces, Draft NO. 4 

dated August, 1993.
If you wish to install an unvented (vent-free) gas log set, only unvented 

gas log sets which have been found to comply with the standard for 

unvented room heaters, ANSI Z21.11.2 are to be installed in this 

fireplace.

OUTSIDE AIR AND DAMPER HANDLE OPERATION

The damper handle, which opens and closes the damper blade, is 

located in the upper front face of the fireplace. Pushing the handle into 

the left of the keyway slot will free the damper blade to automatically 

open. Pushing the handle in to the right will lock the damper blade 

closed (see Figure 22).
The outside air kit handle is located at the left hand side of the fireplace 

(see Figure 22). Pulling the handle out will free the outside air door 

to open. Pushing the handle in will lock the door closed. 

Figure 22 - Damper and Air Kit Handle

OPE

N

CLOS

E

Handle

Outside Air Kit 

Handle

Keyway Slot

Handle Retainer

 WARNING: Risk of fire! Replace grate with IHP 

model 111028-01 (J4491) only. This grate has been 

designed to keep the operation of your fireplace safe 

and efficient.

Summary of Contents for Tuscan36P2

























Reviews: