Astralpool QB600 Owner'S Manual Download

Page: 10 / 16

QB robotic cleaner

Owner’s Manual

QB robotic cleaner

Owner’s Manual

Button Functions

MODE

Start/Stop cleaning

MODE

Select cleaning mode:

MODE

Floor Only

(1h 15 min)

CleansFloor only

MODE

Floor/Walls/Waterline

(2h 30 min)

Cleans the floor, walls and

waterline of the pool

MODE

Elevate System. Remove cleaner

from the pool

4.3

Start / Stop Cleaning

The factory default cleaning mode is Floor/Walls/

Waterline.

Use

MODE

to change cleaning surface setting. Toggle

between modes:

MODE

Floor Only

(1h 15 min) Floor only

MODE

Floor/Walls/Waterline

(2h 30 min)

Floor, walls, waterline

With the cleaner submerged in the water,

press

MODE

to begin operation.

Press again to interrupt and cancel an in-progress

cleaning cycle.

4.4

Elevate System

The Elevate System is designed to assist in retrieving

the robot from the pool. The Elevate System can be

activated at any time during or after a cleaning cycle

and the current cycle will be canceled..

Press

MODE

to begin the automated procedure to

bring the cleaner to the wall.

NOTE

: To stop the procedure at any time, press

and release the button again.

Next, press and HOLD

MODE

to rotate the cleaner.

Once the cleaner is facing the wall of your choice for

retrieval, release the button.

Cleaner will drive forward and up the wall it is facing.

It will wait at the water line to be retrieved.

When in reach, remove the cleaner from the pool

using the handle. The cleaner will quickly expel water

to allow for lighter, easier removal.

NOTE

: Never remove the cleaner from the pool by the

floating cable.

Section 5. Storage & Maintenance

WARNING

To avoid electric shock and other hazards which

could result in permanent injury or death,

disconnect (unplug) the cleaner from the power

source before performing any cleaning and

maintenance.

5.1

Cord Tangling

Tangling can occur more frequently when the

cleaner is not attended to after each cleaning cycle.

The tangle-reducing swivel, in addition to proper

installation, general maintenance and the following

troubleshooting steps can help to avoid cable

challenges.

IMPORTANT

Cleaner power cable may become tangled if

correct procedure is not followed after each

cleaning cycle.

NOTE:

For reduced tangling, the floating cable should

enter the water near the middle of the pool length.

Only place enough cable in the water to reach the

farthest point in the pool.

Summary of Contents for QB600

















Search results

Summary of Contents for QB600

Reviews:

Related manuals for QB600

Brands by name

Popular brands

Astralpool QB600, Owner'S Manual

Search results

Summary of Contents for QB600

Reviews:

Related manuals for QB600

Brands by name

Popular brands