background image

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL THE INSTRUCTIONS

 

CAUTION: Do not plug the power supply into a grounded outlet or do not switch the 

pool cleaner “ON” if it is not fully immersed in water. Operating the cleaner out of water 

will cause severe damage immediately and will result in loss of warranty.

Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its 

cleaning cycle. This will allow the motors to cool adequately. Do not leave the cleaner 

in the pool all the time. Always remember to turn the power supply “OFF” and unplug it 

from the power outlet before removing the cleaner from the pool.

WARNING: The cleaner must not be used when people are in the water. For use 

with swimming pool only

Safety Note

- The unit must be supplied through a residual current device (RCD) having a rated 

residual operating current not exceeding 30 mA 

- The connection to the branch circuit should be consistent with the local and national 

wiring rules (electrical code).

- Mishandling of the unit can result in leakage of lubricants. 

- If the supply cord is damaged, it must be replaced by the manufacturer’s service 

agent or a qualified and trained person in order to avoid hazards. 

  Dear Customer,

Thank you for choosing our product to clean your pool. We hope that you will enjoy 

using your new robot to maintain your swimming pool for years to come.

Before you begin to use your robot, please take a few minutes to carefully read these 

operating instructions.

Again, thank you for choosing our product.

2

Components

Your new automatic pool cleaner contains:

-  The robotic pool cleaner with its floating cable.

-  The Power Supply (transformer).

Please read this manual completely before operating your pool cleaner.

While the appearance of your cleaner and some of its components may differ from those 

shown  here,  the  function  of  the  cleaner,  operating  procedures  and  maintenance 

practices are the same.

WARNING: A Ground Fault Current Interrupter (GFCI-USA) or a Residual Current 

Device (RCD-EUROPE) must be installed to protect your electric outlet and prevent 

any possible electric shock.

This appliance is not intended for use by persons (including children) 

with  reduced  physical,  sensory  or  mental  capabilities,  or  lack  of 

experience and knowledge, unless they have been given supervision or 

instruction concerning use of the appliance by a person responsible for 

their safety. Children should be supervised to ensure that they do not 

play with the appliance.

Side Plate

Handle

Handle Lock

Mechanism

Drive Track

Scrubbing Brush

Unit Body

Outlet Top

SAVE THESE INSTRUCTIONS

Summary of Contents for RF Robotic

















Reviews: