L7714SDSIL Sliding Door Closer
1 x Door Closer
Installation Instructions
Application:
Automatically closes sliding doors.
Door Specifi cations:
• Maximum Door Height 2500mm
• Maximum Door Width 1200mm
• Maximum Door Weight 60kg
• Minimum Reveal Depth
(Door Frame Thickness) 70mm
Tools Required:
• 5mm Hexagonal Allen Key
• Adjustable Spanner
•
Drill
• 2.5mm Drill Bit
• 3.0mm Drill Bit
• Phillips Screwdriver
• Flat Head Screwdriver
Pack Contents
1 x Bent Arm
1 x Straight Arm
1 x 800mm Track
4 x Track Fixing
Screws
1 x Spacer
4 x Closer
Mounting Screws
1 x Wheel and Axle
1 x Wheel Cover
4 x Arm Screws
2. ASSEMBLE THE DOOR CLOSER AND
STRAIGHT ARM
• Place the spacer onto the square
drive shaft.
• Secure the straight arm onto the Closer
unit using the arm screw.
Note:
Arm Orientation - The Straight Arm
square hole has been designed with a 10º
pre-load. Ensure that the straight arm
points away from the side of the closer that
the cover plate attaches to.
3. MARK POSITION
• Measure half the length of the
stationary panel and with a pencil draw
a line 90˚ on the reveal.
• Cut out the template supplied over
page. Align the edge of the template
against the line you drew on the side
facing away from the sliding panel.
• Mark the position of the screw holes
according to the template and drill
ø3mm holes.
4. INSTALL THE DOOR CLOSER
• Install the Door Closer onto the timber
door reveal using the closer mounting
screws
5. INSTALL THE TRACK
Note:
Remove screw cover plug on
the back of the door panel before
attaching track.
• Line up the track with the edge of the
sliding door recess and fl ush with the
inside surface of the sliding panel.
• Drill four ø2.5mm holes into the back
of the door.
• Secure the top of the track only with
two of the four track fi xing screws.
Note:
To secure position - A length of
double sided tape will help hold the track in
position while drilling holes.
077704 0807-1
8. ASSEMBLE THE WHEEL ONTO THE
BENT ARM
• Place a spanner around the axle to hold
it stationary and fi x the arm
screw tightly.
9. SECURE THE BENT ARM ONTO THE
STRAIGHT ARM
• Loosely do up the arm screws in two
of the four holes provided, as far apart
as possible.
• Adjust the overall length of the arm
assembly so that it stays horizontal
when the door is closed, without
hitting the timber reveal.
• Tighten the screws fully.
Note:
Important - Attempt to do this only
once as the tightened screws will damage
the surface fi nish.
10. ADJUST SPEED
• Use a fl at head screwdriver to adjust
the speeds.
• Use a 5mm hexagonal allen key to
adjust the power.
• Check the operation of the door and
readjust as necessary.
Note:
Backcheck Adjustment:
Increases or
decreases cushioning when opening the door
Delayed Action:
Increases or decreases hold
open time
Closing Speed:
Adjusts the speed at which the
door closes
Latching Speed:
Adjusts the speed at the end
of the closing operation
7. FIX TRACK
• Fix the bottom of the track in position
using 2 x track fi xing screws.
1.
BEFORE BEGINNING, MAKE SURE THAT THE SLIDING DOOR IS CLEAN AND FREE SLIDING
. Clean dust and debris from the track. See reverse for the sliding door troubleshooting guide.
6. MOUNT THE WHEEL ONTO
THE TRACK
• Slide the wheel, axle and wheel cover
up into the track from the bottom.
Note:
Ensure axle is pointing out away
from glass.
11. FINISHING
• Slide closer cover into position.
• Press cap over exposed square
spindle.
These surfaces fl ush
