Assa Abloy Interlock IEGL Instructions Manual Download Page 8

Notes

Patent: NZ 556113

IE

G

Linstr  Mar12

ASSA ABLOY New Zealand Limited ©2008 

6 Armstrong Road, Albany, Auckland 0632

www.assaabloy.co.nz

INTERLOCK WARRANTY

ASSA ABLOY New Zealand Ltd (“ASSA ABLOY”) guarantees its Interlock products against defects in workmanship and materials.

All electrical and electronic components used in ASSA ABLOY’s range of products excluding batteries are guaranteed for a period of 12 months from the date of proof of purchase, unless stated 

otherwise.

ASSA ABLOY assumes no liability under the guarantee for the following:

1. Improper installation or failure to follow fitting instructions.

2. Failure due to improper maintenance.

3. Fair wear and tear.

4. Indirect or consequential loss or damage.

5. Cost of removal and/or replacement.

6. Cost of freight and/or travelling time.

7. Damage to or deterioration of plated finishes (soft finishes). As deterioration is possible under some environmental conditions, these finishes are excluded from this guarantee.

8. Any modification or repairs to a product, as supplied, unless authorised by ASSA ABLOY.

9. Use of replacement parts other than authorised parts.

10. Malfunction or failure of the product due to the use of non-genuine ASSA ABLOY parts.

Nothing in the ASSA ABLOY New Zealand Limited Warranty excludes, restricts or modifies any condition, warranty, right or liability implied or protected by law where to do so would render the 

Warranty, or any part of it, void.

Summary of Contents for Interlock IEGL









Reviews: