Interior
Exterior
In
Swing
Exterior
Out
Swing
LATCHING
SPEED
VALVE
BACKCHECK
INTENSITY VALVE
BACKCHECK
LOCATION VALVE
OPTION M71
DELAYED
ACTION VALVE
CLOSING
SPEED VALVE
SPRING POWER ADJUSTER
(5/16 WRENCH or SOCKET)
"
Size of Door
No. of Full
(360°) Turns
Clockwise
of Power
Adjuster
Equivalent
Closer Size
(Approx.)
DC6200 SPRING POWER ADJUSTMENT CHART
2 4 (712)
2 6 (764)
3 0 (915)
3 6 (1067)
' "
' "
' "
' "
4
8
12
16
2
3
4
5
2 6 (764)
3 0 (915)
' "
' "
2 6 (764)
3 0 (915)
3 6 (1067)
4 0 (1219)
' "
' "
' "
' "
Spring Power Adjustment
All DC6200 closers are factory set at an approximate
Size 3.
Adjust closer as necessary for door size using this chart.
Readjustment may be required to suit prevailing conditions.
Locate spring power adjuster from Illustration below
Backcheck Intensity Valve
Turn valve COUNTER-CLOCKWISE to reduce backcheck
or CLOCKWISE to increase backcheck. (Backcheck should
be set to give a soft cushioning action, not a sudden stop.)
Page 8
To Adjust Hold Open (A1 Option)
Open the door to desired position and tighten the hold open
screw firmly (For RH application, turn screw on underside
CLOCKWISE. For LH application, turn screw COUNTER-
CLOCKWISE.) Place the hold open dial over the hex head
of the bracket screw so that one of the slots in the dial is
directly over small screw hole tapped in bracket. Seat the
dial tightly over the bracket. INSERT DIAL SCREW AND
TIGHTEN SECURELY.
(FLAT TIP SCREWDRIVER
W/ 5 (127mm) Min. Shaft Length)
"
Latching Speed Valve
After closing speed has been obtained, turn latching speed valve
CLOCKWISE to SLOW latching or COUNTER-CLOCKWISE to
SPEED latching for last 2 to 5 of door travel.
NOTE: Set combination of CLOSING and LATCHING speeds to
between 3 and 7 seconds Use of door by handicapped,
elderly or small children may require even greater
closing time.
"
"
Closing Speed Valve
To adjust speed of door closing from fully open to a position
2 to 5 from closed, turn Closing Speed Valve CLOCKWISE
to SLOW closing, COUNTER-CLOCKWISE to SPEED
closing.
"
"
Delayed Action Valve
Turn valve CLOCKWISE to SLOW closing, COUNTER-
CLOCKWISE to SPEED closing. Delayed action may be
adjusted from 20 seconds to 90 seconds, depending on
degree of door swing. Delay occurs at the beginning of the
door closing cycle from fully open down to 70°, where the
closing speed valve then begins its control.
h
ct
a
L
d
e
e
p
S
g
ni
s
o
l
C
h
e
k
c
c
c
k
a
B
ye
la
d
e
D
t
io
c
n
A
Option
M-71
Full Cover
(Standard)
Slip cover over closer. Hold tightly
against closer mounting surface.
Secure on each side with 6-32 x
1/4 PBHMS screws.
"
(3/32 Allen Wrench Provided)
(3/32 Allen Wrench Provided)
(3/32 Allen Wrench Provided)
Installing Cover
Power
Size
Stamp
Date Stamp
HOLD OPEN
SCREW
DIAL
DIAL
SCREW
®
ASSA ABLOY
Copyright© 2005, 2012 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.
80-9330-3000-152
Rev. 05/12
DC3200 Size 1 thru 6 Adjustment See Chart
