Assa Abloy Corbin Russwin ED5400 (A) Series Installation Instructions Manual Download Page 12

Page: 12 / 16

Surface Vertical Rod

Installation Instructions

Exit Devices

FM164 09/19

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • [email protected]

Plastic Installation Template for ED5000 Exit Devices

For use in conjunction with instruction sheets and door marker templates packed with exit device. Holes

and slots are identified below by exit device series and trim. Prep door and frame for only those features

required for the exit device being installed.

Frame

Door Stop

Door

Template

Figure 20

Vertical

reference

All ED5000 exit devices

Concealed vertical rod

Against frame stop

or mullion (when

applicable). For reim and

SecureBolt exit devices

All ED5000 exit devices

Vertical reference

Mortise

Rim and

SecureBolt

Horizontal

reference

Against door

surface

Trim only

Summary of Contents for Corbin Russwin ED5400 (A) Series

















Search results

Summary of Contents for Corbin Russwin ED5400 (A) Series

Reviews:

Related manuals for Corbin Russwin ED5400 (A) Series

Brands by name

Popular brands

Assa Abloy Corbin Russwin ED5400 (A) Series, Installation Instructions Manual

Search results

Summary of Contents for Corbin Russwin ED5400 (A) Series

Reviews:

Related manuals for Corbin Russwin ED5400 (A) Series

Brands by name

Popular brands