background image

5

CL3300 Series

Installation Instructions

Cylindrical Lockset

FM533  02/20

Copyright © 2012, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole 

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin 

1-800-543-3658 • [email protected]

Cylinder Installation (continued)

Interchangeable Core Removal

1.  Insert key marked CONTROL and turn clockwise approximately  

15˚. (Figure 10

2.  Pull core and tailpiece completely out of lever. 

Install Standard Cylinder

1.  Make sure lock is unlocked.
2.  Make sure cylinder tailpiece is aligned  

in same direction as cylinder bible.

3.  Slide cylinder all the way into lever.

•  For 6-pin cylinder: Fold retainer at  

hinge and press fit retainer halves  

together as shown.

•  For 7-pin cylinder: Break retainer at  

hinge and discard spacer section.  

Also remove black cylinder spacer  

from inside of chassis rollback  

for clearance. 

Standard Cylinder Tailpieces
Note:

Dimensions are given in inches (

"

)  

and millimeters (mm).

Conversion Kit for Schlage

®

 Cylinders with CL3300 Lockset

1.  Remove threaded collar and Schlage

®

 tailpiece. 

2.  Install CL3300 tailpiece with threaded collar.
3.  Adjust collar for proper end play of plug.

Control Key

Core

Figure 10 

 

11/16"

(17 mm)

7/8"

(22 mm)

6 PIN

7 PIN

ACTUAL SIZE SHOWN

Lever

Retainer

Cylinder

Cylinder 

Bible
Cylinder      

Tailpiece

Fold Retainer Halves

Actual Size Shown

For 7-pin Cylinder

7-pin

6-pin

7/8"

(22 mm)

11/16"

(17 mm)

For 6-pin Cylinder

Hinge

Hinge

Remove Spacer

and Discard

Figure 11 

 

Figure 12 

 

Schlage

®

 

Cylinder

Threaded 

Collar

Schlage

®

 

Tailpiece

Summary of Contents for Corbin Russwin CL3300 Series









Reviews: