ASROCK J4005B-ITX Manual Download Page 15

English

13

J4105B-ITX
J4005B-ITX

2.3  Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on 

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is 

“Open”. 

Clear CMOS Jumper

(CLRMOS1)

(see p.1, No. 5)

Short: Clear CMOS 

Open: Default

CLRMOS1 allows you to clear the data in CMOS. The data in CMOS includes 

system setup information such as system password, date, time, and system setup 

parameters.  There are two ways for you to clear and reset the system parameters 

to the default setup. Please turn off the computer and unplug the power cord, then 

you may either short the solder points on CLRMOS1 by using metal material, 

e.g., a paper clip for 3 seconds; or you may use a jumper cap to short the pin on 

CLRMOS1 for 3 seconds. Please remember to remove the paper clip or the jumper 

cap after clearing the CMOS.

2-pin Jumper

*The jumper cap is not provided. 

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option 
“Clear Status” to clear the record of previous chassis intrusion status.

Summary of Contents for J4005B-ITX




















Reviews: