background image

47

CPU Voltage

  It allows you to adjust the value of CPU voltage. However, for safety and 

system stability, it is not recommended to adjust the value of this item.  

GFX Engine Clock

  Use this to adjust graphics engine clock. The default value is [Auto].

 DRAM 

Confi guration

 DRAM 

Frequency

If [Auto] is selected, the motherboard will detect the memory module(s)
inserted and assigns appropriate frequency automatically.

 

DRAM Timing Control

 

Power Down Enable

Use this item to enable or disable DDR power down mode.

 Bank 

Interleaving

Interleaving allows memory accesses to be spread out over banks on the 
same node, or accross nodes, decreasing access contention.

 Channel 

Interleaving

It allows you to enable Channel Memory Interleaving. Con  guration  op-
tions: [Disabled], [Auto]. The default value is [Auto].

 

CAS# Latency (tCL)

 

 

Use this item to change CAS# Latency (tCL) Auto/Manual setting. The

 

 

default is [Auto].

 

RAS# to CAS# Delay (tRCD)

 

 

Use this item to change RAS# to CAS# Delay (tRCD) Auto/Manual setting.

 

 

The default is [Auto].

 

Row Precharge Time (tRP)

 

 

Use this item to change Row Precharge Time (tRP) Auto/Manual setting.

 

 

The default is [Auto].

Summary of Contents for A55 Pro3






































































Reviews: