background image

 

 

 

 

 

 

OM00020 Rev 2, FP00091, FP00101 Operation Manual 

Page 

10

 of 

15

 

 

Press 

 4 times to return to the main screen. 

Parameter Tree 

The table below represents all the functionality of the controller. Some items are only accessible by 
entering the login password (see Controller Login p. 11): 

Table 1: RMC Controller Tree 

Level 1 

Level 2 

Level 3 

Level 4 

ALA 

Alarms 

AAL 

Active alarms 

  

  

  

  

  

  

LOG 

Log history 

  

  

  

  

  

  

CLR 

Clear log history 

  

  

  

  

LOG 

Login 

  

  

  

  

  

  

Str 

Start 

On 

Turn On 

  

  

  

  

  

  

Off 

Turn Off 

  

  

  

  

  

  

RST 

Reset Alarms 

  

  

  

  

PAR 

Parameters 

GEN 

General 

StU 

Setup 

y01 

ON/OFF 

  

  

  

  

  

  

y05 

Temperature units 

  

  

  

  

  

  

y07 

Restore default parameters 

  

  

  

  

  

  

y08 

 Control sensor 

  

  

  

  

  

  

y09 

 Control mode 

  

  

  

  

ALA 

Configuration 

BUZ 

Buzzer activation time 

  

  

  

  

  

  

AdL 

Alarm relay activation delay 

  

  

  

  

  

  

AOF 

Alarm relay active if unit in OFF 

  

  

  

  

Ser 

Serial Settings 

Ser 

Serial address (Modbus) 

  

  

  

  

  

  

bAU 

Serial baudrate (Modbus) 

  

  

  

  

  

  

COM 

Serial settings (Modbus) 

  

  

  

  

PAS 

Password 

L01 

Password level 1 

  

  

  

  

  

  

L02 

Password level 2 

  

  

  

  

  

  

L03 

Password level 3 

  

  

CFG 

Unit configuration 

Set 

Setpoint 

  

  

  

  

  

  

c01 

Pump flow delay 

  

  

  

  

  

  

c02 

Fan delay off 

  

  

  

  

  

  

c03 

T1-Pv filter 

  

  

  

  

  

  

c04 

Alarm difference 

  

  

  

  

  

  

c05 

Pump shutdown delay 

  

  

  

  

  

  

c06 

Min compressor speed 

  

  

  

  

  

  

c07 

Pump speed 

  

  

  

  

  

  

c08 

Compressor delay off 

  

  

  

  

  

  

c09 

 Max pump speed 

  

  

  

  

  

  

c10 

 Min pump speed 

  

  

  

  

PID 

PID Settings 

P01 

Regulation type 

  

  

  

  

  

  

P02 

Gain 

  

  

  

  

  

  

P03 

Integral time 

  

  

  

Summary of Contents for FP00091
















Reviews: