ASM Zip-Spray 1700 Operation, Repair, And Parts Download Page 7

Page: 7 / 38

309421

Component Identification and Function

Electric motor (inside of enclosures)

Provides mechanical power to pump

Power switch

For manually turning on/off electrical power to motor (“I” is ON / “0” is OFF)

Pressure Control knob

For manually increasing (turn clockwise) and decreasing (turn
counter-clockwise) fluid pressure in pump, hose, and spray gun

Pump fluid outlet fitting

Threaded connection for paint hose

Fluid filter

Filters fluid coming out of pump to reduce tip plugging and improve finish

Self cleans during pressure relief

Piston pump (behind black cap)

Pumps and pressurizes fluid and delivers it to paint hose if necessary. Black
cap permits quick removal of outlet valve.

Suction tube

Draws fluid from paint pail into pump

Prime tube (with diffuser)

Drains fluid in system during priming and pressure relief

Spray/Prime/Drain valve control

Directs pressurized fluid to paint hose in SPRAY position (pointing forward)

Directs fluid to drain tube in PRIME/DRAIN position (pointing down)

Automatically relieves system pressure in overpressure situations

Fluid inlet connection and inlet valve

Where suction tube connects to pump and inlet valve

Inlet screen

Prevents debris from entering pump

Paint hose

Transports high-pressure fluid from pump to spray gun

Airless spray gun

Manually-controlled, hand-held on/off device for fluid being sprayed

Tip base

Reduces risk of fluid injection injury

Super Zip spray tip

Atomizes fluid being sprayed, forms spray pattern, and controls fluid flow
according to hole size

Reverses for unplugging without disassembly

Trigger safety lever

Prevents accidental triggering of spray gun

Gun fluid inlet fitting

Threaded connection for paint hose

Swivel

Allows spray gun to swivel without twisting paint hose

Gun fluid filter (in handle)

Filters fluid entering spray gun to reduce tip plugging and improve finish

Hose/Cord wrap bracket

Stows paint hose and electrical cord

Pail hanger

For transporting pail by its handle

Summary of Contents for Zip-Spray 1700







































Search results

Summary of Contents for Zip-Spray 1700

Reviews:

Related manuals for Zip-Spray 1700

Brands by name

Popular brands

ASM Zip-Spray 1700, Operation, Repair, And Parts

Search results

Summary of Contents for Zip-Spray 1700

Reviews:

Related manuals for Zip-Spray 1700

Brands by name

Popular brands