background image

40

309879

ASM Standard Warranty

ASM warrants all equipment referenced in this document which is manufactured by ASM and bearing its name to be free from defects

in material and workmanship on the date of sale by an authorized ASM distributor to the original purchaser for use. With the exception

of any special, extended, or limited warranty published by ASM, ASM will, for a period of twelve months from the date of sale, repair or

replace any part of the equipment determined by ASM to be defective. This warranty applies only when the equipment is installed,

operated and maintained in accordance with ASM’s written recommendations.

This warranty does not cover, and ASM shall not be liable for general wear and tear, or any malfunction, damage or wear caused by

faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-

stitution of non--ASM component parts. Nor shall ASM be liable for malfunction, damage or wear caused by the incompatibility of ASM

equipment with structures, accessories, equipment or materials not supplied by ASM, or the improper design, manufacture, installa-

tion, operation or maintenance of structures, accessories, equipment or materials not supplied by ASM.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized ASM distributor for

verification of the claimed defect. If the claimed defect is verified, ASM will repair or replace free of charge any defective parts. The

equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect

in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and

transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT

NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE

.

ASM’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other

remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any

other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the

date of sale.

ASM MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT

NOT MANUFACTURED BY ASM

. These items sold, but not manufactured by ASM (such as electric motors, switches, hose, etc.), are

subject to the warranty, if any, of their manufacturer. ASM will provide purchaser with reasonable assistance in making any claim for

breach of these warranties.

In no event will ASM be liable for indirect, incidental, special or consequential damages resulting from ASM supplying equipment here-

under, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of

warranty, the negligence of ASM, or otherwise.

FOR ASM BRAZILIAN/CANADIAN/COLUMBIAN CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings

entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English.

TO PLACE AN ORDER OR FOR SERVICE

, contact your ASM distributor,

or call ASM

1--800--854--4025

to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication. ASM reserves the

right to make changes at any time without notice.

MM 309879

ASM Company, 3500 North 1st Ave., Sioux Falls, SD 57104

www.asmcompany.com

PRINTED IN USA 309879K

4/2003 Rev. 1/2006

Summary of Contents for 2300









































Reviews: