Asko DBI865IGXXL, Operating Instructions Manual

Page: 11 / 28

Night mode
Lower noise level during the dishwashing program. The program time
is extended.
Intensive mode
Improves the dishwashing results, but the dishwasher uses more energy
and water. The program time is extended.
Select an Option
To select an option, press the option button until the desired option is
shown on the display. The available options vary between programs.
Extra Dry
A higher temperature in the final rinse and a longer drying cycle
improve the drying results if you activate this option. Energy
consumption is slightly increased.
Delayed Start
When you select Delayed Start, the dishwasher will start in 1-24 hours
after you have pressed the button Start/Stop and closed the door.
1. Press the button once to activate Delayed Start. Press the button
several times – or hold it in – to set the desired number of hours.
2. Press Start/Stop and close the door. The timer counts down and
the dishwasher starts after the selected delay.
If you want to cancel the Delayed Start option, open the door then
press and hold Start/Stop for three seconds.
START
STOP
Starting the dishwasher
Press Start/Stop until the display shows "Program started, close door".
This indicates that the dishwasher is ready to start. Close the door
properly, otherwise the dishwasher will not start.
If the dishwasher is not started or the door is not closed within 2 minutes
of the last button press, the machine switches off.
Time remaining
Once you have chosen a program, a program mode and options, the
time the program took when last used is displayed.
Once you have started the dishwasher, the display shows the remaining
program time. The remaining time is updated after the water for the
final rinse has been heated.
This may differ somewhat from time to time depending on the
temperature of the water supply, the amount of dishes, the ambient
temperature and other factors.
During the first run of each program, the remaining time displayed can
be slightly misleading, as the dishwasher is estimating the time. When
you run the program a second time, the dishwasher will calculate the
remaining time based on the previous duration of the program.
0:21
Time remaining
Status indicator
The status indicator on the front display provides information by means
of different colours.
Activate the Info in front display setting. See the chapter Settings.
Blue - Load more
The program has started, but you can still load more dishes.
Red - Do not load
You should not load any more dishes (risk of poorer dishwashing result).
Flashing red indicates a problem. See also Chapter Troubleshooting .
Green - Unload
The dishwashing program is finished. Standby light for 60 minutes.
Stopping or changing a program
If you want to change program after starting the dishwasher, open the
door then press and hold Start/Stop for three seconds. Add more
detergent if the lid of the detergent dispenser has opened. Then choose
a new program, press Start/Stop and close the door.
If you want to load more dishes
Open the door. The dishwasher stops automatically. Add the dishes
and close the door. After a while, the dishwasher continues the
program.
If the dishwasher is turned off due to a
power failure
If the dishwashing program was not finished, the interrupted program
continues when power is restored.
NOTE!
During drying, the program is interrupted if the power is cut or the
door is open for more than 2 minutes.
Once the program has finished
Once the program has finished, “END” appears on the display.
At the end of the program, you will hear a short beep. Chapter Settings
describes how to change this function.
The dishwasher switches off automatically after the program ends.
Turn off the water tap after each use.
How to get the best drying results
• Fully load the dishwasher.
• Angle dishes with hollows, such as cups, so that the rinse water
will run off. This is also important for plastic items.
• Top up with rinse aid or increase the rinse aid dosage level.
• Activate the Extra Dry option.
• Activate the High temperature setting. See the chapter Settings.
• Open the door a little once the program has finished.
• Allow the dishes to cool before unloading the dishwasher.
Unloading the dishwasher
Hot porcelain is more fragile. Leave the dishes to cool in the dishwasher
before unloading them.
Unload the lower basket first to avoid any water drops from the upper
basket falling onto the dishes in the lower basket.
11