Asko D5893 Operating Instructions Manual Download Page 41

Page: 41 / 52

Customer Care Center

1-800-898-1879

www.askousa.com

1. Connect drain hose

The drain hose is routed to an inlet plug on

the sink unit’s water trap.

Cut the drain hose adapter to the appro pri-

ate size for connection to the undersink drain

or garbage disposer.

The overall length of the

drain hose must not exceed 1 feet 9 inches.

No part of the drainage hose may be more

than 7-1/ inches (90 mm) above the bottom

of the dishwasher. The hose must not be run

directly to the floor drain or similar.

The hose must always discharge at least 1-

/ inches (0 mm) above the bottom of the

dishwasher.

. Connect water supply hose

Use the supplied O ring and tighten the con-

nection by hand plus a quarter turn with a

wrench. Open the shutoff valve and let the

pressure settle for a while. Check the connec-

tions again to make sure they are not leaking.

. Connect the plug

Ensure that the power outlet is within the range

of the power cable. Do not use an extension

cord!

The dishwasher must be connected to a

grounded

outlet.

Plug

Water connection

Shutoff
valve

Grounded

outlet

Grounded

outlet

37-1/2”

Max 950mm

13-3/4”

Min- 350mm

Clamp

Hose barb
coupling

Step 4. Connecting electricity, water and drain

Summary of Contents for D5893





















































Search results

Summary of Contents for D5893

Reviews:

Related manuals for D5893

Brands by name

Popular brands

Asko D5893, Operating Instructions Manual

Search results

Summary of Contents for D5893

Reviews:

Related manuals for D5893

Brands by name

Popular brands