background image

28

Problems

Possible  causes

Action

Water remains in the
machine.

Bad odour in the machine

The dishes are not
sufficiently dry

pump) can be heard from
the machine, this does not
stop when the power is
switched off using the main
power switch.

• Obstruction in the drain
hose.

• Kinks in the drain hose.

• The filters are clogged.

• Items in the drain pump.

• Dirt along the strips and in

corners

• Drying power too low.
The machine is not fully
loaded.
The rinse aid has run out or
the set dose is too low.

2. Pull out the plug.
3. Call a service engineer

• Disconnect the drain hose
where it is connected to the
sink’s water trap. Check that
no debris has become stuck.
Is the cone-shaped part of
the pipe cut so that the
diameter is at least 16 mm?

• Check that the hose is free
from kinks or sharp bends.

• Clean out the coarse filter,
the fine filter and the filter.

• Clean out the drain pump.
See chapter on cleaning

• Clean with a dish brush

and low-lather detergent.

• Activate the Normal drying
option (not all models).
Put a full load in the
machine.
Replenish rinse aid or
increase the dose of rinse
aid.
Open the door slightly once
the program has finished.

Summary of Contents for D3430









































Reviews: