Ashly VCM-88C Operating Manual Download Page 8

Page - 8

Operator Manual – VCM-88C Controller

Copyright© 2007 – Ashly Audio Inc.

 Applications & Configurations

To make any configuration changes, the top of the VCM-88C must be removed.  Be sure
to disconnect all cables & power before opening the unit.  Jumper settings are illustrated in
the table & diagrams below.

Single Connector Insert

To use a mixing console’s single jack insert capabilities with the VCM-88C, an internal
jumper must be selected to properly configure the input and output connections.  Once
configured the input is on the tip and the output is on the ring of the In jack. The Out jack
is not used.

Single Channel Pass-Through

When Using Master Output for personal monitor mixing or other application, it is possible
to pass a channel’s input directly to it’s output jack, eliminating the need for extra “Y”
cables when daisy-chaining. The VCA circuit’s output signal is still summed to the Master
Output, but is removed from the channel output jack.

Input/Output Matrixing

Input Matrixing means that an input can be internally routed to one or more additional
channel inputs, particularly useful in distributed zone applications. Each of the matrixed
VCA channels share a common input signal but retain their distinct level controls via the
RD-8C, RW-8C, or other hardware or software controllers.

Jumper

Pin

Description

J 05

O

Not Used

T

Bypass VCA on Channel

J 04

V

Enable VCA on Channel

1

Single Jack TRS Insert (T=In, R=Out)

2

Dual Jack In/Out

J 02

P

Not Used

M1

Channel Input Mix Bus 1 Assign

M2

Channel Input Mix Bus 2 Assign

M3

Channel Input Mix Bus 3 Assign

J 07

PT

Channel Input pass-through to VCA

M1

Channel VCA Source Selected from M1 Bus

M2

Channel VCA Source Selected from M2 Bus

M3

Channel VCA Source Selected from M3 Bus

J 08

PT

Channel VCA Source from pass-through input

Default settings in 

BOLD

Jumper Settings with Signal Flow

Safety Instructions – 3

Introduction - 4

VCM-88C Controller – 5

Connectors & Cables - 5

Physical Description - 6

Installation – 7

Applications - 8

Insert
Pass-Through
Matrixing

Jumper Settings

Data Connections – 9

Troubleshooting – 11

Dimensions - 11

Specifications - 12

Warranty - 13

Summary of Contents for VCM-88C















Reviews: