PEMA Models
4125
8125
4250
8250
Continuous Average Power: Output Per Channel, Low Z Models, Stereo
Mode, 20Hz–20kHz, 1%THD, All Channels Driven
4 Ohms
125W
125W
250W
250W
8 Ohms
75W
75W
150W
150W
Low Z Output: Bridge Mode, 20Hz–20kHz, 1% THD, All Channels Driven
8 Ohms
250W
250W
500W
500W
70V, 100V Distributed Output: 20Hz–20kHz, 1% THD, All Channels Driven
70V (per channel)
125W
125W
250W
250W
100V (per channel)
125W
125W
250W
250W
Line Current Draw: 120V, All Channels Driven
Standby Mode
190mA
290mA
190mA
290mA
Idle (no signal)
590mA
565mA
540mA
565mA
1/8 Max Power, Pink Noise, All Channels Driven
Typical
1.70A
2.78A
2.85A
5.0A
1/3 Max Power, Sine Wave, All Channels Driven
Maximum
3.72A
5.78A
3.00A
5.50A
Thermal Dissipation: BTU/hr, All Channels Driven
Standby Mode
46.7
63.8
46.7
63.8
Idle (no signal)
123
187
123
187
1/8 Max Power, Pink Noise, All Channels Driven
Typical
232
444
341
700
1/3 Max Power, Sine Wave, All Channels Driven
Maximum
251
481
378
775
Signal to Noise
20Hz–20kHz, Unweighted >102dB
>102dB
>105dB
>105dB
PEMA™ sets a new industry benchmark for value-engineered
zone sound systems. By seamlessly merging our powerful,
open-architecture DSP functionality paired amplifier per-
formance inside a two-rack space unit, PEMA lowers overall
system cost, occupies less space, improves energy efficiency,
and both speeds and simplifies system installation and
programming. Four and eight amplifier channel versions
are available at both 125 and 250 Watts per channel.
Full 96kHz performance is available on 32-bit SHARC
processors for utterly transparent audio.
PEMA changes the way consultants and integrators approach
sound system design. With only the addition of input sources
and output speakers, PEMA delivers an elegant solution with
less cabling, less rack space, and less installation time, using
proven DSP and amplifier technology that will awe clients
with its simplicity, sophistication, and reliability.
In addition to DSP algorithms such as ambient noise compen-
sation, advanced automatic feedback suppression, automatic
mixer, and a full complement of filters, EQs, delays, and the
like, PEMA offers DSP control of the amplifier functionality
as well: selection of bridge-mode operation, HPF settings for
constant voltage system networks, stereo-linking of channel
pairs, MIC/LINE/TEL-PAGE functions on channel 1, full control
of ducking priorities, and full-range remote-gain control
capability.
PEMA’s I/O count and formats are ideal for small to mid-sized
installations. Each variant has eight balanced input channels
that are software selectable for mic or line levels. The first
channel may also be set for a transformer isolated, TEL-PBX
level. Additionally there are eight pairs of summed-mono RCA
connectors optimized for consumer line level devices. Eight
preamp auxiliary outputs allow integrators to route
signals from the matrix mixer to anywhere the system
requires.
As a member of the respected Protea™ DSP lineage,
PEMA is remarkably easy to program and deploy. All set
up is accomplished using standard 10/100 Ethernet
protocol and our Protea™ ne Software on a PC platform.
Hot-plug DSP placement allows users to insert any function
into any channel block, even when running live audio.
Automatic DHCP network IP configuration reduces network
set up time. Lockable front panel controls and multi-level
software security with password access guarantee a tamper-
proof audio system.
PEMA Features:
• CobraNet® and Dante® network audio fully supported
• 8-in x 8-out sophisticated matrix mixing
• 8 built-in mic pre’s
• Gain sharing automatic microphone mixing (Automixer)
• Automatic feedback suppression
• Ambient noise compensation
• Dedicated telephone/PBX input
• Dual RCA and balanced euroblock inputs
• Post DSP AUX line level outputs
• Stereo summed to mono
• Event scheduling (RTC)
• Adjustable HP/LP filters
• Built-in pink/white noise & sine wave generator
• Full suite of Ashly Protea™ DSP
• Hot-plug DSP placement
• 96kHz or 48kHz sample rate
• 32-Bit SHARC DSP
• 24-Bit A/D–D/A audio resolution
• 15V phantom power for mic inputs
• Full control using Ashly software over 10/100 baseT Ethernet
• Easy and intuitive user interface
• Automatic DHCP network IP configuration
• Euroblock connectors for preset recall, DC remote level
control and serial data control
• External control via Ashly standard wall remotes, Ashly
Ethernet wall remotes or Ashly Remote iPad® App
• Level control via variable DC control voltage
• Stand-By mode activation via contact closure
• Multi-level Security
• Safety/Compliance:
c
TUV
us
, CE, FCC, RoHS
pema
4125
pema
4250
pema
8125
pema
8250
pema
™
p
rotea
-e
quipped
m
edia
a
mplifier
Front Panel LED Indicators
Unit Status
POWER
Blue
Switch: On, Off
STANDBY
Yellow
Standby, flashing
PROTECT
Red
On, Off
DISABLE
Yellow
On, Off
COM
Green
On, for Ethernet data or Device ID
Each Channel
SIGNAL LEVEL
Red
Clip/Mute
Yellow
-6dB
Green
-18dB, -12dB
BRIDGE
Green
Per Channel
TEMP
Yellow
Per Channel
CURRENT
Green
Per Channel: Proportional to output
70V Rated
100V Rated
5-Year Warranty
Hand-built in
Webster, NY
Ashly Audio, Inc.
847 Holt Road
Webster, NY 14580 USA
+1-800-828-6308 US toll free
+1-585-872-0010 tel
+1-585-872-0739 fax
u
u
www.ashly.com
u
© 2014 All features, specifications and graphical representations are subject to change or improvement without notice.
Ashly Audio is a division of Jam Industries, Ltd. DS-1 1213
