B ( 0.15 : 1 )
C ( 1 : 5 )
D ( 0.30 : 1 )
B
C
D
PARTS
INSTRUCTION
RH BACK - 4
BASE - 2
2
4
POSITION RH BACK '4' UP TO BASE PANEL '2'
ENSURING HOLES ARE ALIGNED AND THAT
THE BACK CENTRAL FOLD IS POSITIONED IN
THE CUTOUT SLOT IN THE BASE.
SCREW THE PANELS TOGETHER.
4*
PARTS
INSTRUCTION
6
RH SIDE - 6
POSITION THE RH SIDE '6' UP TO THE PRE
ASSEMBLED BACK AND BASE ENSURING ALL
HOLES ARE ALIGNED, SCREW TOGETHER.
ON THE FRONT TWO FIXING HOLES POSITION
ONE COVER PLATE '9' IN THE CORNER,
ALIGNING FIXING HOLES, SCREW IN POSITION.
(THE COVER PLATE HIDES THE EXPOSED
SCREW POINTS)
COVER PLATE
- 9
COVER PLATE
PARTS
PARTS
INSTRUCTION
16*
LH BACK - 3
3
13*
LOCATE LH BACK PANEL '3' INTO THE BASE AND
RH BACK AS SHOWN ENSURING THAT IT SLOTS
INTO THE CENTRAL BASE CUTOUT AND THAT
THE CENTRAL VERTICAL FOLDS ARE
CORRECTLY ALIGNED.
SCREW TOGETHER ALONG THE BASE AND
VERTICAL JOINT.
5
LH SIDE - 5
PARTS
INSTRUCTION
INSTRUCTION
INSTRUCTION
INSTRUCTION
INSTRUCTION
PARTS
PARTS
PARTS
PARTS
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
STEP 8
COVER PLATE
- 9
REPEAT STEP 2 WITH LH SIDE '5' AND
THE REMAINING COVER PLATE '9'
16*
1
10
TOP - 1
DOOR
STOP - 10
POSITION DOOR STOP '10' ON THE
INSIDE OF THE FRONT OF THE TOP '1'
AS SHOWN. ALIGN WITH THE 3
CENTRAL HOLES AND SCREW TOGETHER.
THE LARGE CIRCULAR HOLES ALLOW
ACCESS FOR THE FIXING SCREWS.
3*
TOP - 1
DOOR
STOP - 10
1
POSTION THE PRE-ASSEMBLED TOP PANEL
OVER THE CARCASE AS SHOWN ENSURING
THAT THE ASGARD LABEL IS ON THE FRONT
RH SIDE OF THE TOP CHECK HOLES FOR
ALIGNMENT & SCREW IN POSITION.
SEALANT
TO HELP PREVENT WATER INGRESS WE
RECOMMEND APPLYING A BEAD OF
'ALL
WEATHER SEALANT'
ON THE FRONT CORNER
JOINTS AS SHOWN PRIOR TO FITTING THE
DOORS.
18*
7
8
LH DOOR - 7
RH DOOR - 8
WE RECOMMEND THAT YOU USE HAND HELD
DRIVERS RATHER THAN POWER DRIVERS WHEN
FIXING THE DOORS. IT IS IMPORTANT TO
SUPPORT THE DOORS AT ALL TIMES WHEN
FITTING THE SCREWS TO ENSURE CORRECT
ALIGNMENT AND SO NOT TO DAMAGE THE
THREADED INSERTS.
ALIGN HINGES OF LH DOOR '7' ( NON
LOCKING) AND RH DOOR '8' (LOCKING)
SCREW IN POSITION.
18*
LEVELLERS
- 14
SEALANT
HAVING FITTED THE DOORS IT MAY BE
NECESSARY TO USE THE LEVELLING SHIMS
'14' UNDER THE CORNERS OF THE UNIT IN
ORDER TO ACHIEVE AN EVEN GAP AROUND
THE DOORS AND ENABLE THEIR SMOOTH
OPERATION.
WE RECOMMEND APPLYING AN ADDITIONAL
BEAD OF SEALANT ALL ROUND THE OUTER
EDGE OF THE UNIT WHERE IT COMES INTO
CONTACT WITH THE CONCRETE OR FLAGGED
BASE.
Summary of Contents for VANGARD
Page 1: ......
