Aseptico ADU-40CF Command Air Operation, Maintenance & Service Manual Download Page 8

Page 8

6. Drain and disconnect the intake hose. Disinfect all hoses which have come into contact with waste

water using a dilute bleach solution.

7.  Store  the  intake,  cold  water  and  drain  hoses  along  with  the  alternate  source  regulator  in  the

plumbing pouch. Be sure to coil tubing carefully to avoid kinking. Dry components as thoroughly

as possible before storage.

8.Disconnect the ON/OFF foot switch, power cord, and instrument tray. Store these items in the

electronics accessories pouch. Disconnect optional soap dispenser if used and flush out the soap

spout. Pack and store dispenser components in pouch. 

9.  Twist  loose  and  remove  the  four  sink  legs,  or  optional  leg  supports  if  used.    Fold  and  store

components in their appropriate pouches.

10. Place the sink into the case with the sink sides aligned with the case handles. Store the plumbing

and electrical pouches, and optional soap dispenser pouch if used, in the sink basin. Lower the

sink spout, or slide the Locking Cap up the tube and pivot the optional 15-inch spout forward until

it lies flat with top surface of basin.

11.Store the leg and optional leg-support pouches in the lid. Place the lid and secure all perimeter

latches. 

Reference figure A

Daily cleaning

All hoses which have come in contact with waste water during operation must be disinfected with a

dilute bleach or equivalent solution, prior to storage. Disinfect exposed sink parts in accordance with

conventional medical/dental practice.

Daily functional checklist

Observation of the following conditions will ensure that the ADU-40CF is functioning normally.

1. The green L.E.D. by the spout lights when the unit is connected to a power source.
2. The pump can be heard running when the ON/OFF footswitch is depressed.  
3. The spout is fully extended.
4. When the tank is filled the orange L.E.D. lights indicating the heating element is operating.
5. Once primed, the intake lines retain their water level when the pump is not operating.

Summary of Contents for ADU-40CF Command Air

















Reviews: