manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 59

TeleBoss 830 2.11.370 STD User Manual 

 

Page 59 

 

If the changes are made via a Web session, any Web interface changes will not take effect until the Web 

session has been closed. 

 

 

 

 

EventSensor Reporting Settings 

EventSensor Reporting is a feature that allows an EventSensor connected to one Asentria product to transmit 

data to another Asentria product via a TCP connection. This feature does not need to be enabled in order to 

allow for normal alarm notice delivery. 

 

At this software version, EventSensor reporting is only functional from the Command Line Interface. 

 

For a further explanation of EventSensor Reporting and how to configure both the Host and Client units, refer 

to the 

EventSensor Reporting - Feature Guide

 on the Asentria Information Portal or contact 

Asentria 

Technical Support

. 

 

The 

client

 unit is the TeleBoss with the sensor physically connected to it and the 

host

 unit is the TeleBoss to 

whom the client unit will report when there is a change in the status of its sensor. 

 

In addition to configuring the settings defined below, each sensor on the Client unit will need to have 

EventSensor Reporting Enabled in the Alarm/Event Definitions / EventSensor Device Settings / Individual 

EventSensor Slots

 configurations settings. 

 

 
TeleBoss 830 EventSensor Reporting Settings 
A) EventSensor Report To IP                          [] 
B) EventSensor Report To Port                        [4000] 
C) Enable EventSensor Reporting Host                 [OFF] 
D) EventSensor Reporting Host Port                   [4000] 
 

 

Event Sensor Report To IP

  

Use this field to set

 the IP address of the host unit a sensor connected to this TeleBoss would report to. 

 

Event Sensor Report To Port

  

This option sets

 the TCP Port that a sensor connected to this TeleBoss would use to report to a host Asentria 

device.  Default setting is 4000. 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands