manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 107

TeleBoss 830 2.11.370 STD User Manual 

 

Page 107 

 

 

There are some new version EventSensors with six possition DIP Switches.  The first two switches would 

need to be set to zero (

toward numbers on the label) and they othewise operate the same as a four 

possiton DIP switch.

 

 

For one wire ESJ style sensors the settings slot will automatically be assigned to it if one is available. 

 

The dip switches on the EventSensor define the slot number you wish that sensor to display at.  On the 

command interface menu shown below option "B" is slot "1" and option "Q" would be slot "16".  Option "A" 

is the Internal IO card option, which is referred to as slot "200". 

 

 
TeleBoss 830 - Sensor Events Menu 
   Name                  ID         Alive      Number     Configuration 
A) INTERNAL              --------   -          200        2-CC  
B) unnamed               0301F5C4   Y          1          8-CC 
C)  <none>    
   ... 
Q)  <none> 
R) Sensor Unresponsive Settings 
 

 

EventSensor Slots

 

(A thru Q)  

The A-

Q options display the settings menu for the EventSensor set to the numbered slot.   “A” is always 

reserved for the internal or on-board sensors and is number 200.  If an Expansion card is installed it will 

occupy slot 1 and will be accessed via option B.  Any external EventSensors will be listed at menu 

options B 

– Q and will be numbered 1 – 16. The number refers to the slot number set with the DIP 

Switches as outlined above. 

 

Sensor Unresponsive Settings

  

This option displays the Sensor Unresponsive Menu where you can configure the actions the TeleBoss 

takes if an EventSensor becomes unresponsive. 

 

 

EventSensor Slots (A thru Q) 

The display for each EventSensor will vary depending on configuration. EventSensors can be configured with 

varying combinations of sensors. This manual will go over just one of the many types of EventSensor setups.  

The different types of EventSensors will have different options to configure but each will have a similar set up 

page.  Refer to the 

EventSensor and SensorJack Sensor Feature Guide

 for more information. 

 

 

Note:

 if you are installing a new EventSensor into a slot that was previously occupied by another sensor 

the settings need to be cleared.  Choose the B-

Q option that needs to be cleared then select option “Clear 

Settings 

for This EventSensor” and respond to the confirmation question.  Once the slot is clear a new 

sensor can be configured for the slot. A restart or a power cycle would be required for the new 

EventSensor to be recognized by the TeleBoss. 

 

 
TeleBoss 830 - Internal Events Menu 
A) Device Name                                      [INTERNAL] 
B) Contact Closure 1                                [unnamed] 
C) Contact Closure 2                                [unnamed] 
D) EventSensor Reporting Enabled                    [OFF] 
 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands