ASDQMS GageMux Operating Manual Download Page 1

 
 
 
 

 

 

Operating Manual

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GageMux

®

 

 

4 Input Gage Interface 

Operating Manual 

 

GageMux

®

 

www.spcanywhere.com 

ii 

(248) 370-9919 

 

 
 
 
 
 

Information in this document is subject to change without notice and does not represent a 
commitment on the part of Advanced Systems and Designs, Inc.  No part of this manual may 
be reproduced or transmitted in any form or by any means, electronic or mechanical, 
including photocopying and recording, for any purpose without the express written 
permission of ASD. 
 
The ASD and GageMux

® 

logos are registered trademarks of Advanced Systems and Designs, 

Inc. 
 
Copyright © Advanced Systems and Designs, Inc., 1984-

2004

.  All rights reserved.  

 
Printed and bound in the United States of America. 
 
Document No. 10040PF 

 
 
 

Advanced Systems and Designs, Inc. 

2142

 

Pontiac

, Suite 

202

 

Auburn Hills

, MI  48

326

 

Phone:  (248) 

370

-

9919

 

Fax:  (248) 

370

-

9921

 

Email:  support@

spcanywhere

.com 

Website:  http://www.

spcanywhere

.com 

Summary of Contents for GageMux











Reviews: