min. 60
55
min. 100
min. 80
Mounting position (mm)
Ascon Tecnologic S.r.l.
via Indipendenza 56,
27029 - Vigevano (PV)
Tel.: +39 0381 69871,
Fax: +39 0381 698730
www.ascontecnologic.com
Installation
Manual
Contents
- General description
- Accessories
- Installation
- Electrical connections
- Electric safety
1
Model identification label (on the back side of the module);
2
DIN RAIL 35 x 7.5 (EN50022);
3
X1
one 2 poles plug to connect the power supply and
X2...
X3
two 3 poles plugs to connect the DO1...DO2 SPDT output relays or
Vdc/Vac SSR or 12 Vdc to drive external SSR;
4
X4...
X6
two 5 poles plugs to connect the DI1... DI12 Digital Inputs;
5
Status/diagnostic LEDs:
L1
(red, CAN ERR)
USB
(green, USB activity/CAN Run),
COM2
(green, COM2 traffic),
COM1
(green, COM1 traffic),
MSG
(message),
RUN
(program status run/stop),
PWR
(power supply ON);
6
- Reset button;
7
X17
USB type A receptacle to connect a flash drive;
8
X10
5 poles plug to connect the COM1 service serial port (RS232/RS485);
9
X11
3 poles plug to connect the COM2 serial port (RS485);
10
X9
2 poles plug output power supply (15Vdc);
11
X7...
X8
6... 7 poles plugs to connect DO3... D10 SPST output relays;
General description
Accessories
Installation
24 VDC Power supply
APS2ALEDR12024 (120 W, 5.0 A),
APS2ALNDR75-24 (75 W, 3.2 A),
APS2ALMDR20-24 (20 W, 1.0 A)
1
Open the 2 spring slides on the lower
part of the CPU,
clip the upper part of
the module to the rail;
2
Rotate the module downwards, then
close the 2 spring slides
;
3
Switch OFF the Power Supply
Lower the spring slide by inserting a
flat-blade screwdriver as indicated
;
4
Turn and lift the module upwards to
remove the CPU from the DIN rail.
Dimensions (mm)
Mounting the module
- Mount the module vertically;
- In order to help the ventilation flow of
air, respect the distances between
modules and walls or other modules.
Mounting position
Mounting/removing the modules
on/from the DIN rail
Removing the module
Operating conditions
Integrated system,
CPU module with
on-board I/O
mod.
M81
mod.
M81
M . I . M 8 1 - 0 4 / 1 7 . 0 5
C o d . I S T R - M M 8 1 E N G 0 4
Rail mounting
DIN 35 x 7.5
(EN 50022)
110
175
60
60
Environmental condition
B
Suggestion
Operating
conditions
T
Temperature
0...+50°C
%Rh
Umidity:
5... 95% Rh
non condensing
Special
conditions
T
Temperature
> 50°C
Use forced
ventilation
%Rh
> 95% RH
Warm up
P
Conducting
atmosphere
Use filter
Forbidden
conditions
C
Corrosive
atmosphere
E
Explosive
atmosphere
1
2
3
4
3
4
14
15
11
12
13
5
6
7
9
10
8
12
X14...
X15
5 poles plugs to connect AI5... AI12 NTC/PT1000 Analogue Inputs;
13
X16
RJ45 plug to connect the Ethernet TCP/IP network for programming purposes
or for the MODBUS through the TCP port;
14
X13
6 poles plug to connect AO1... AO4 Analogue Outputs;
15
X12
7 poles plug to connect AI1... AI4 Analogue Inputs.
Note:
The green terminals on the CPU are male connectors (pitch 5 mm), the
corresponding female plugs are snap-on connectors with screw or spring
terminals for connecting the wires.
E
Screw Terminal Blocks
APS2/M81-kITSCREW
Disposal
The appliance (or the
product) must be
disposed of separately in
compliance with the local
standards in force on
waste disposal.
