ASCOM teleCARE IP Installation Manual Download | Manualshive

Page: 159 / 206

background image

DRAFT

TD 93021US

17 July 2017 / Ver. PF3

154

Installation Guide
teleCARE IP

8.7.5 NIRX teleCARE IP Transceiver

The NIRX transceiver is a printed circuit module which is piggy back mounted on the NIRC3 room
controller and the NIFX fixed transceiver. The NIRX will adds wireless call functionality to the NIRC3 room
controller and the fixed transceiver. Optionally the NIRX can also be mounted on the NILF location beacon
for actively monitoring the state of the NILF, such as tamper and low battery alarm conditions.

Figure 200. Transceiver piggyback module (NIRX)

8.7.6 Connecting the Transceiver Module

The NIRX is piggyback mounted on the NIRC3 room controller, on the NIFX fixed transceiver and on the
NILF low frequency beacon printed circuit boards:

Figure 201. Piggyback mounting of the transceiver module on the NIRC3 and NIFX

Note:

The NIFX is delivered with an NIRX mounted from the factory.

NIRC3

NIFX

Factory

mounted

Optional

«
...
157
158
159
160
161
...
»

Summary of Contents for teleCARE IP















































































































































































































Reviews:

No comments

Related manuals for teleCARE IP

Clearspan 6731i

Brand: Aastra Pages: 8

Brand: Aastra Pages: 37

Brand: Aastra Pages: 3

Brand: Aastra Pages: 2

Brand: Aastra Pages: 15

Brand: Aastra Pages: 22

Brand: Aastra Pages: 44

Brand: Aastra Pages: 24

Brand: Aastra Pages: 2

Brand: Aastra Pages: 3

Brand: Aastra Pages: 29

AastraLink Pro 160

Brand: Aastra Pages: 230

Brand: Aastra Pages: 45

Brand: Aastra Pages: 112

Brand: 8x8 Inc Pages: 47

Brand: Aastra Pages: 2

Brand: ATCOM Pages: 9

Brand: Xblue Networks Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands