Asco 460 Installation & Operation Manual Download Page 11

Page: 11 / 24

For troubleshooting, call technical assistance at 1-800-237-4567 or [email protected]

IO-70064

05/2020

ASCO 460/465/480/485 Surge Protective Device (SPD)

Installation

Special Enclosure

Considerations

Wiring

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe

electrical work practices. See NFPA 70E, CSA Z462 or NOM-029-STPS.

•

This equipment must only be installed and serviced by qualified

electrical personnel.

•

Turn off all power supplying this equipment before working on or inside

equipment.

•

Always use a properly rated voltage sensing device to confirm power is

off.

• Replace all devices, doors and covers before turning on power to this

equipment.

•

This equipment must be effectively grounded per all applicable codes.

Use an equipment-grounding conductor to connect this equipment to the

power system ground.

Failure to follow these instructions will result in death or serious injury.

The recommended conduit entry is at the bottom or either side of the device

enclosure. Use a conduit seal that is appropriate for the enclosure rating.

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe

electrical work practices. See NFPA 70E, CSA Z462 or NOM-029-STPS.

•

This equipment must only be installed and serviced by qualified

electrical personnel.

•

Turn off all power supplying this equipment before working on or inside

equipment.

•

Always use a properly rated voltage sensing device to confirm power is

off.

• Replace all devices, doors and covers before turning on power to this

equipment.

•

This equipment must be effectively grounded per all applicable codes.

Use an equipment-grounding conductor to connect this equipment to the

power system ground.

•

Confirm the SPD voltage rating on the module or nameplate label is the

same as the operating voltage.

• Do not touch the bottom located terminals which are energized with the

switch in either the ON or OFF positions.

Failure to follow these instructions will result in death or serious injury.

DANGER

Conduit Location and

Recommendations

Removing and Reconnecting the

RJ45 Diagnostic Cables

If the unit has Active Surge Monitor (ASM) routing of the RJ-45 wiring may

be required. Please refer to ASCO document IO-70109.

Summary of Contents for 460

























Search results

Summary of Contents for 460

Reviews:

Brands by name

Popular brands

Asco 460, Installation & Operation Manual

Search results

Summary of Contents for 460

Reviews:

Brands by name

Popular brands