background image

© 2020 ASCO Power Technologies. All Rights Reserved

For access to self-service tools and chat support visit se.com/us/en/work/support  or call 1-888-778-2733 for technical assistance

12

IO-70065

01/2020

ASCO 335 Surge Protective Device (SPD)

Wiring

Note: Mount the unit as close as possible to the protected panel. 

1. 

Identify breaker location and SPD location.  See figure 2 below.

2. 

Confirm SPD is rated for your system by comparing voltage measure

-

ments to the Line Voltage (L1 – L2 for split phase or L-N for single 

phase). L1-L2 should be 240 Vac and L-N will be 120 Vac. 

3. 

Turn off all power supplying this equipment before working on or inside 

any enclosure containing this equipment.

4. 

Determine mounting location.  See figure 2 below. 

5.  Remove an appropriately sized knockout from the panel. 

6.  Mount SPD.  Weather resistant applications require additional sealing, 

etc.  See figure below. 

7.  Install in accordance with national and local electrical codes and match 

the branch circuit Overcurrent Protection Device (OCPD) to the wire 

size.  Recommended breaker size is 30 A and wire size 10 AWG. 

8.  Do not loop wires.  Trim excessive wire length.

Figure 2:

 Typical panel Installation

Surface Mount Installation

L1

L2

G

N

BREAKER

 

Use closest  

breaker to SPD

 

Locate SPD close to 

intended breaker

 

Keep Leads Short as 

Possible

 

Avoid Sharp Bends

 

Rotate Model 

335 such that 

LED indicators 

are most visible

 

Outdoor installation requires 

appropriate weather sealing 

at nipple (gasket, sealing 

conduit, etc.)

Loads

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

•  For outdoor installation use an appropriate weather sealing at the nipple 

(o-ring, sealing conduit, etc.)

Failure to follow these instructions will result in death or serious injury.

DANGER

Summary of Contents for 335

















Reviews: