manualshive.com logo in svg

Asante AsanteFAST 10, Installation Manual

Share
Download
Asante AsanteFAST 10 Installation Manual Download Page 27

 

Page 5-4

 

Asanté SNMP MacAgent

 

4

 

Select SNMP MacAgent. 

 

5

 

Select MacTCP while pressing down the Shift key. 

 

6

 

Click Install.

 

7

 

Restart your Macintosh.

 

Configuring MacTCP 

 

To configure MacTCP, perform the following steps:

 

1

 

Select Control Panels from the Apple menu.

 

2

 

Double-click the MacTCP icon. The MacTCP Configuration 
screen appears. 

 

∆

 

Note:  To configure MacTCP, see the MacTCP Adminis-
trator’s Guide.  This guide is included with the Asanté-
View documentation.

 

3

 

Double-click More... and select Manually. This allows you to man-
ually enter your IP address.

 

4

 

Close the MacTCP control panel.

 

∆

 

Note:  If you have any questions about your MacTCP
or SNMP configuration, contact your network adminis-
trator. It is important that the network administrator
be aware of any changes on the IP network.

 

NBAsanteFast Ch 5 SNMP Agent  Page 4  Wednesday, August 21, 1996  10:29 AM

Summary of Contents for AsanteFAST 10


































Reviews:

No comments

Brands by name

Popular brands

Load more brands