manualshive.com logo in svg

AS MOTOR Allmaher AS 21 4T B&S, Operator'S Manual

Share
Download
AS MOTOR Allmaher AS 21 4T B&S Operator'S Manual Download Page 19

19

Maintenance and cleaning

Improper maintenance can make the device unsafe for operation and result in accidents. Regular
maintenance keeps you device ready for use.

Service the device according to the following maintenance instructions.

Contact an authorised service centre if problems during maintenance occur or if you determine de-
ficiencies during one of the following inspections.

Component

Action

Maintenance
interval

A

B

Device

Check for safe working condition (basic inspection).

■

▲

Clean.

■

Customer service.

▲

Fuel

Check fuel level.

■

Is the tank cap closed?

■

Tank, fuel valve,
and fuel line

Check parts for leaks and check for good condition.

■

▲

Carburetor

Does the carburetor close again after starting?

■

▲

Ventilation grid

Clean.

■

▲

Engine cooling

Clean.

▲

Spark plug

Check/replace.

▲

Air filter

Maintain.

■

■▲

Blade and fasten-
ing components

Check for wear and damage. See chapter Checking the
blade.

■

▲

Change.

▲

Motor brake

Does the blade stop within 7 seconds?

□

▲

Release the drive
lever

Does the device stop when the lever is in zero position?

□

▲

Drive

Check.

■

▲

V-belt

Are the belts tensioned correctly, without fissures, and in
good condition?

▲

Bowden cables

Check for proper function and ease of movement.

■

▲

Chassis and impact
protection

Check for rust and fissures and check the welding seams.

■

▲

Are all protective devices and covers in place, fastened
correctly and properly functioning?

■

▲

Label

Condition of the labels.

■

▲

Summary of Contents for Allmaher AS 21 4T B&S





































Reviews:

No comments

Brands by name

Popular brands

Load more brands