background image

Warranty

All products are covered from date of purchase 

by a two-year return to base warranty. 
By return to base, we mean that the customer 

is responsible for all costs of transport to and 

from Artistic Licence.

Returns  will  not  be  accepted  without  prior 

authorisation. In order to discuss a request to 

return goods, please email: 
 

[email protected]

CE Compliance

Rail-Demux is CE compliant when installed 

in a shielded and earthed metal case

Compliance

All Products manufactured or sold by 

Artistic Licence Engineering Ltd are fully 

compliant with the appropriate CE and RoHS 

regulations.  Product  specific  information  is 

available on request.
 

Waste Electrical & Electronic Equipment  

(WEEE)

Artistic Licence is a member of a WEEE 

compliance scheme and will happily recycle 

any of our products that you, at your expense, 

return to us. 

Due to our policy of continuing product improvement 

specifications are subject to change without notice

Artistic Licence

 

The Mould Making Workshop

Soby Mews

Bovey Tracey

TQ13 9JG

United Kingdom

Telephone    +44 (0) 20 8863 4515

Email:             [email protected]

Web:    

www.ArtisticLicence.com

[email protected]

Summary of Contents for Rail-Demux










Reviews: